cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
362
Views
0
Helpful
1
Replies

IDSM-2 not booting up after System Image ugrade

gautamzone
Level 1
Level 1

Hi friends,

I had attempted to upgrade the WS-SVC-IDSM2 blade on Cisco 6509 (Sup 720) switch to SW ver 6.0(3) from Maintenence partition 2.1(2) but was unsuccessful. The IDSM-2 was initially running ver 5.1(3).

The file that i tried was WS-SVC-IDSM2-K9-SYS-1.1-a-6.0-3-E1.bin.gz.

I followed the instructions as per the Configuration Guide for Installing System images but still failed on this.

Now, the module fails to boot.

I am only able to log into the maintainence partition after using the command hw-module module 3 reset cf:1.

But I am not able to log into the application partition after using the command hw-module module 3 reset hdd:1.

When i execute show images command in Maintainence partition, i still see the version listed as 5.x.

Running show module on the switch when booting the IDSM-2 in application partition yields the following output:

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAD100204GU

2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1006CMLY

3 8 Intrusion Detection System WS-SVC-IDSM-2 SAD09440284

4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1030WDL9

5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1003ASLQ

<Output truncated>

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0015.62e1.9eb4 to 0015.62e1.9eb7 2.2 12.2(14r)S5 12.2(18)SXF3 Ok

2 0016.c7a1.0644 to 0016.c7a1.065b 2.3 12.2(14r)S5 12.2(18)SXF3 Ok

3 0012.80f1.7f28 to 0012.80f1.7f2f 6.0 7.2(1) 8.5(0.46)RFW PwrDown

4 0018.7354.b1b0 to 0018.7354.b1df 2.4 12.2(14r)S5 12.2(18)SXF3 Ok

5 0013.c346.c3e8 to 0013.c346.c3eb 4.5 8.1(3) 12.2(18)SXF3 Ok

<Output truncated>

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

1 Centralized Forwarding Card WS-F6700-CFC SAL10019FCU 2.0 Ok

2 Centralized Forwarding Card WS-F6700-CFC SAL1007DDH2 2.0 Ok

3 IDS 2 accelerator board WS-SVC-IDSUPG ADEI5313870 2.3 PwrDown

4 Centralized Forwarding Card WS-F6700-CFC SAL1028UK0W 2.0 Ok

5 Policy Feature Card 3 WS-F6K-PFC3B SAL1003AVFH 2.2 Ok

5 MSFC3 Daughterboard WS-SUP720 SAL1003AN8W 2.4 Ok

7 Centralized Forwarding Card WS-F6700-CFC SAL1008E7D7 2.0 Ok

Mod Online Diag Status

---- -------------------

1 Pass

2 Pass

3 Not Applicable

4 Pass

5 Pass

6 Pass

7 Pass

8 Pass

9 Pass

After I unplug the module from slot and replug it, the module comes online but only boots still into maintenence partition.

I dont have a service account also. Have any of you come across this issue?

Any directions on this will be really appreciated.

Thanks a lot

Gautam

1 Reply 1

b.hsu
Level 5
Level 5

Remove blades from chassis, allowing drive to cool down, this is a known defect that is addressed in software starting with 4.1(4)4

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: