cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
977
Views
19
Helpful
6
Replies

How do you decipher facility codes on Q931 traces

littledavewhite
Level 1
Level 1

I have an issue on site with divert messages across a qsig link. The customer is diverting calls from an sx2000 pabx to callmanager via a MGCP gateway. I need to understand the facility codes and how to decipher them ?

6 Replies 6

hi in my debug isdn q931 i have the following message, what do i paste into the decode tool

Facility i = 0x9FAA068001008201008B0100A1190202017B06052B0C024E01300C8004303030300A0102040144

Hi,

Could you please paste the whole debug isdn q931. This encoder looks like is not recognizing:

9F AA 06 80 01 00 82 01 00 8B 01 00 A1 19 02 02 01 7B 06 05 2B 0C 02 4E 01 30 0C 80 04 30 30 30 30 0A 01 02 04 01 44

hi the full decode

*Jul 17 15:13:56.102: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x00B6

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Facility i = 0x9FAA068001008201008B0100A1100202018B020100300780055350415245

Facility i = 0x9FAA068001008201008B0100A1190202018C06052B0C024E01300C8004303030300A010204014A

Calling Party Number i = 0x4980, '3769'

Plan:Private, Type:Subscriber(local)

Called Party Number i = 0x80, '2399'

Plan:Unknown, Type:Unknown

*Jul 17 15:13:56.118: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x80B6

Channel ID i = 0xA98381

Exclusive, Channel 1

*Jul 17 15:13:56.122: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x80B6

Progress Ind i = 0x8088 - In-band info or appropriate now available

*Jul 17 15:13:56.246: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x80B6

Facility i = 0x9FAA06800100820100A1110201020201028009566F6963656D61696C

Connected Number i = 0x0081, '2399'

*Jul 17 15:13:56.262: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x00B6

*Jul 17 15:14:08.734: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x00B6

Cause i = 0x8090 - Normal call clearing

*Jul 17 15:14:08.778: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x80B6

*Jul 17 15:14:08.790: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x00B6

I've attached the decode of the Setup and Connect message.

Hope this helps

hi this is very good but i was looking for some information on the decode for future ref, did you manage to get the decode tool working?

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: