WAN Router Help

Unanswered Question
Jul 24th, 2007
User Badges:

I was given a task to change over a site from one provider to another. I do not have site access as of yet so I am gathering information remotely.



a sh run shows no T1 controllers and only a serial interface with an IP. Then a Fa0 with an IP.


Now the serial interface as no channel groups or timing line encoding on it.


The router is a 1721


SO I am assuming there is an external CSU/DSU on location.


The new provider will not have one and its only a smart jack.


According to the sh ver listed below. There is a WIC-T1-dsu


now my question is, I am not 100% sure it has a built in CSU/DSU.


I pasted below a sh ver and Sh diag. Can someone give me some information on will this router work. Like can I just run RJ45 from the smart jack and connect it to the router?




Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-Y-M), Version 12.2(4)YA2, EARLY DEPLOYMENT RELEAS

E SOFTWARE (fc1)

Synched to technology version 12.2(5.4)T

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Thu 11-Apr-02 21:54 by ealyon

Image text-base: 0x80008124, data-base: 0x807976DC


ROM: System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)

ROM: C1700 Software (C1700-Y-M), Version 12.2(4)YA2, EARLY DEPLOYMENT RELEASE SO

FTWARE (fc1)


York_1721 uptime is 31 weeks, 5 days, 19 hours, 50 minutes

System returned to ROM by power-on

System image file is "flash:c1700-y-mz.122-4.YA2.bin"


cisco 1721 (MPC860P) processor (revision 0x100) with 29492K/3276K bytes of memor

y.

Processor board ID FOC062002RR (2465657608), with hardware revision 0000

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

WIC T1-DSU

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)


Configuration register is 0x2102



#sh diag

Slot 0:

C1721 1FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

PCB Serial Number : FOC062002RR

Part Number : 73-7546-01

Board Revision : A0

Fab Version : 04

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 5A 41 01 00 C1 8B 46 4F 43 30 36 32

0x10: 30 30 32 52 52 82 49 1D 7A 01 42 41 30 02 04 FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF


WIC Slot 0:

FT1

Hardware revision 1.3 Board revision C0

Serial number 0027926602 Part number 800-03279-04

Test history 0x00 RMA number 00-00-00

Connector type WAN Module

EEPROM format version 2

EEPROM contents (hex):

0x20: 02 11 01 03 01 AA 20 4A 50 0C CF 04 00 00 00 00

0x30: 60 00 00 00 02 03 19 01 FF FF FF FF FF FF FF FF


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
sundar.palaniappan Tue, 07/24/2007 - 07:26
User Badges:
  • Green, 3000 points or more

It appears you have an integrated T1 WIC CSU/DSU. You should be able to connect the T1 cable directly to the SJ. If you want to change any of the CSU/DSU default configuration you need to use the 'service-module' command under the Serial interface.


HTH


Sundar

bryan.farmer Tue, 07/24/2007 - 12:32
User Badges:

Agree with last post, you have an integrated T1 WIC.


You'll see it if you issue a show interface


The service-module commands will only show in the config if you change defaults (ie - b8zs/esf/timeslots 1-24).


And yes, it uses an RJ45 connection.

Actions

This Discussion