07-26-2007 01:48 AM
The network topology is
Modem --> [FXS][cisco 2821][E1] --> ISDN PRI --> [E1][cisco 2811][PVDM2-36DM]
ISDN PRI link is operated correctly, debug isdn q931 shows that connection is established. Info message is
*Jul 23 06:27:45.407: %ISDN-6-CONNECT: Interface Serial1/0:1 is now connected to 555 N/A
Unfortunately, no carrier signal is going from modem to line.
Configuration of Cisco Routers is below.
1st (2821)
==========
!
controller E1 0/2/0
framing NO-CRC4
pri-group timeslots 1-2,16
!
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn incoming-voice modem
no cdp enable
!
dial-peer voice 1 pots
destination-pattern 555
port 0/3/0
!
voice-port 0/3/0
cptone RU
!
dial-peer voice 888 pots
destination-pattern .T
port 0/2/0:15
!
2nd (2811)
==========
!
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-2,16
!
interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn not-end-to-end 64
isdn protocol-emulate network
isdn incoming-voice modem
no cdp enable
!
line 0/322 0/357
modem InOut
07-26-2007 02:40 AM
Hello,
What is the E1 hardware you are using ? (do show diag to know). The PVDM2-DM works only with NM-xT1/E1.
07-26-2007 02:56 AM
> The PVDM2-DM works only with NM-xT1/E1.
Yes, of course, it is well known fact. We are using NM-1CE1T1-PRI. See "show diag" output below.
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
PCB Serial Number : FOC11070F5L
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-03
Board Revision : A0
Deviation Number : 0
Fab Version : 03
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20070214
Chassis Serial Number : FHK1109U00A
Chassis MAC Address : 001b.2aa3.c1c8
MAC Address block size : 24
CLEI Code : COM7C00ARA
Product (FRU) Number : CISCO2811
Part Number : 73-10258-04
Version Identifier : V04
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 31 30 37 30 46 35 4C 40
0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 03 42 41 30
0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00
0x30: 09 87 83 01 32 3F 46 C2 8B 46 48 4B 31 31 30 39
0x40: 55 30 30 41 C3 06 00 1B 2A A3 C1 C8 43 00 18 C6
0x50: 8A 43 4F 4D 37 43 30 30 41 52 41 CB 8F 43 49 53
0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
0x70: 04 89 56 30 34 20 D9 02 40 C1 FF FF FF FF FF FF
PVDM Slot 0:
36 port PVDMII digital modem PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-10102-03
Board Revision : C0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC10354YRW
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-36DM
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 04 90 41 01 00 82 49 27 76 03 42 43 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 30 33 35
0x20: 34 59 52 57 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8A 50 56 44 4D 32 2D 33 36 44 4D 89 56 30 31 20
0x40: D9 02 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 1:
NM-1CE1T1_PRI Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-21550-02
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : FOC104753CA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Fab Part Number : 28-5935-03
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Product (FRU) Number : NM-1CE1T1-PRI
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 9D 41 01 00 C0 46 03 20 00 54 2E 02
0x10: 42 41 30 80 00 00 00 00 02 03 C1 8B 46 4F 43 31
0x20: 30 34 37 35 33 43 41 03 00 81 00 00 00 00 04 00
0x30: 85 1C 17 2F 03 C4 08 00 00 00 00 00 00 00 00 C5
0x40: 08 00 00 00 00 00 00 00 00 CB 8D 4E 4D 2D 31 43
0x50: 45 31 54 31 2D 50 52 49 89 56 30 31 20 FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
07-26-2007 03:33 AM
Which exact IOS version are you using ?
07-26-2007 04:27 AM
Initial IOS version is c2800nm-ipbase-mz.124-11.T.bin
Also were tested
c2800nm-ipvoicek9-mz.124-15.T1.bin
c2800nm-ipbasek9-mz.124-15.T1.bin
07-26-2007 05:55 AM
Hi, have you configure modem country as per documentation ?
http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a00806b941f.html
07-26-2007 06:35 AM
Do you mean "modem country v12
Yes, command "modem country v12 russia" is in configuration of second router (with PVDM2-36DM)
07-26-2007 10:03 AM
Then I wouldn't know what to suggest and you may need to give the case to the TAC for help.
07-29-2007 09:42 PM
The problem is solved. IOS command "network-clock-select 1 E1 1/0" was needed at the beginnig of router configuration (2nd router with E1 PRI and PVDM2-36DM).
07-30-2007 01:15 AM
Thanks for letting us know. The command is mandatory in all T1 ? E1 application however it didn't occurred to me to ask if you had it.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: