cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1228
Views
0
Helpful
15
Replies

Cisco 827, no cd

mathieuallaert
Level 1
Level 1

When I connect the adsl cable, the CD led gives no signal.

The RX/TX led's are flashing very fast.

When I do a 'debug atm events', I get :

Router#debug atm events

ATM events debugging is on

Router#

00:18:53: DSL: 20: Modem state = 0x8

00:18:56: DSL: Could not establish connection

00:18:59: DSL: Trying to bring up DSL line using Embedded firmware version : 3.9

.19

00:18:59: DSL: Send ADSL_OPEN command.

00:18:59: DSL: Using subfunction 0x2

00:18:59: DSL: Using subfunction 0x2

00:18:59: LOCAL:Max noise margin for power cutoff 31

00:18:59: DSL: Sent command 0x3

00:19:02: DSL: 1: Modem state = 0x8

00:19:04: DSL: 2: Modem state = 0x8

00:19:07: DSL: 3: Modem state = 0x8

00:19:09: DSL: 4: Modem state = 0x8

00:19:12: DSL: 5: Modem state = 0x8

00:19:14: DSL: 6: Modem state = 0x8

And the ATM interface is down.

No administrative down, but just down.

I can't get it up.

15 Replies 15

nikolay-shopik
Level 1
Level 1

If the modem state stays at "0x8" and says "Could not establish connection," it means that the Cisco ADSL WIC has not heard from the central office (CO). It does not see an incoming signal.

http://www.cisco.com/warp/public/794/wicadsl_lyr1.html

nikolay-shopik
Level 1
Level 1

And I can tell you w/o looking in debug if you have no CD link you should check wire and RJ connector. It's like don't hear dial tone if you pickup your phone, physical problem.

Hi, thanks for you're response.

But I have already checked the cable + swichted of cable.

Is it normal that the RXD/TXD leds are flashing the whole time ?

The cisco faq says :

ADSL TXD

Green

Blinks when an ADSL port sends data.

But my router is not connected yet to adsl. (Stil no CD)

Does another adsl modem works when connected to the same line? Which IOS do you have on the 827 ?

I tested the line with a thomson speedtouch 510 and a Linksys wag54g without promblems.

My ios version is Version 12.4(13b)

Bootstarp vrsion : 12.2(11r)YV6

Hi,

can you upgrade to 12.4T that has the latest firmware 3.9.220 ?

Also, can you try tweaking some settings for dsl as per document:

http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_feature_guide09186a00801a6d12.html

this is a bit of trial and error attempt. But chances are it can help. I would set "dsl operating-mode itu-dmt" first.

Hi,

I have tried to set "dsl operating-mode itu-dmt" first, but it didn't work. There is no change

I can't update to another version, i haven't such a account.

And the dsl commands that i tried where not recognized by the router

Is "dsl noise-margin" accepted ? Which commands are shown if you do "dsl ?"

I found the real problem.

I have a wrong adapter !

Can I order on the cisco site a correct one ?

What adapter are you talking about ?

You cannot order directly from cisco. What is that you need, chances are you can get it on the leading auctions website.

On this page :

http://www.cisco.com/en/US/products/hw/routers/ps380/products_field_notice09186a0080154dcb.shtml

It says that I need a +12V and -12V line.

On my adapter 34-0875-01, there is no -12V / +12V available.

Hi,

You might have an 827H, the model with the 4-ports hub. In that case, no 12V is required from the power adapter;

http://www.cisco.com/en/US/docs/routers/access/800/827/hardware/installation/guide/specs.html#wp1013951

Hi,

No it's the 827 model. Without the 4-ports hub.

Just Console - Ethernet - ADSL - Power

Then it's missing more voltages than just 12V !

It may be difficult to find an original PS. Perhaps you can use an "additional external one" just for the +/- 12V. You don't need the -24 and -71 that are for loop current and ring generation on the telephone ports of the 827-4V.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: