2611 help

Unanswered Question
Jul 28th, 2007
User Badges:

in another post I am getting this error...


System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1999 by cisco Systems, Inc.

TAC:Home:SW:IOS:Specials for info

C2600 platform with 32768 Kbytes of main memory


open: file "n" not found

open(): Open Error = -1

loadprog: error - on file open

boot: cannot load "flash:n"


I have done everything that people are saying, format flash xmodem installed new OS ...


Was wondering if anyone would mind working with me and remote in with me to take a look and possible resolve my problem.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
balajitvk Sat, 07/28/2007 - 22:45
User Badges:
  • Silver, 250 points or more

Hi,


When you encouter this problem??? After copying new IOS to flash?? Which mode it is going, rommon mode ?? what is the bootstring you given??


Rgs

rdaggett1 Sun, 07/29/2007 - 05:33
User Badges:

yes this is happening after loading a new IOS, I get that error over and over until i do a break to rommon. at rommon i type boot and it boots.

balajitvk Sun, 07/29/2007 - 09:19
User Badges:
  • Silver, 250 points or more

Hi,


This looks like a mismatch of ios file name in the bootstring and actual one.... Once you booted thro. boot command see the output of show boot and show flash for the spcified boot file name...... Also see the boot sytem flash command in the show run output.....


Accordingly if you corrected this, i hope u can get out of this problem......


Still required, pls. paste the show flash and show run command output.


Rate if it does,

Rgs

rdaggett1 Sun, 07/29/2007 - 12:29
User Badges:

here is the info requested


sh running-config


Current configuration : 621 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot system flash:c2600-io3-mz.123-15a.bin

boot-end-marker

!

!

no aaa new-model

ip subnet-zero

ip cef

!

!

!

ip audit po max-events 100

!


sh flash


Router#sh flash


System flash directory:

File Length Name/status

1 8041044 c2600-io3-mz.123-15a.bin

[8041108 bytes used, 8736104 available, 16777212 total]

16384K bytes of processor board System flash (Read/Write)


Router#


AND SH STARTUP-CONFIG


Using 628 out of 29688 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot system flash:c2600-io3-mz.123-15a.bin

boot-end-marker

!

!

no aaa new-model

ip subnet-zero

ip cef

!

!

!

ip audit po max-events 100

!

!



They all allok to be the same file .... thanks for you help .. any ideas?



rdaggett1 Sun, 07/29/2007 - 12:45
User Badges:

wondering what private-config and ifIndex is ....


Directory of nvram:/


27 -rw- 621 startup-config

28 ---- 5 private-config

1 -rw- 0 ifIndex-table

balajitvk Sun, 07/29/2007 - 20:47
User Badges:
  • Silver, 250 points or more

Hi,


As you mentioned, it seems to be same.... But your first output shows that it is trying to open flash:n which is bit confusing....


What about your show boot and show version config register output....


Rgs,

rdaggett1 Mon, 07/30/2007 - 05:18
User Badges:

sh ver


IOS (tm) C2600 Software (C2600-IO3-M), Version 12.3(15a), RELEASE SOFTWARE (fc2)


Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Thu 21-Jul-05 19:55 by dchih

Image text-base: 0x80008098, data-base: 0x80D545B8


ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

ROM: C2600 Software (C2600-IO3-M), Version 12.3(15a), RELEASE SOFTWARE (fc2)


Router uptime is 15 hours, 55 minutes

System returned to ROM by reload

System image file is "flash:c2600-io3-mz.123-15a.bin"


cisco 2611 (MPC860) processor (revision 0x202) with 28672K/4096K bytes of memory

.

Processor board ID JAB031408JN (2668064774)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

2 Ethernet/IEEE 802.3 interface(s)

2 Serial network interface(s)

32K bytes of non-volatile configuration memory.16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102


I am sorry I am having a hard time finging the sh config register and sh boot commands ....

smothuku Mon, 07/30/2007 - 03:37
User Badges:
  • Silver, 250 points or more

Hi ,


what is the config register value (0x2102)?

can you paste show version output of the router.


and type


boot system flash:image.bin in privilege mode and reload the router.


cheers :)

satish


Actions

This Discussion