VPN passthrough w/ PIX 6.3(5)-No data received

Unanswered Question
Jul 31st, 2007

I recently swapped out a DD WRT gateway/router with a PIX 501, and now I can not connect to the VPN at work (asa 5510) with the Cisco VPN client.


I was able to connect before no problem, the PIX connects to a SBC dsl modem. Bytes in is zero, however bytes out goes up. I am able to log in just fine, I get an IP address, and seem to be connected.


Any help would be much appriacheated, this problem is driving me nuts!


my config:

PIX Version 6.3(5)

interface ethernet0 10full

interface ethernet1 10full

nameif ethernet0 outside security0

nameif ethernet1 inside security100

enable password yHJEhTyJX51EDD.A encrypted

passwd yHJEhTyJX51EDD.A encrypted

hostname pixfirewall

domain-name ciscopix.com

fixup protocol dns maximum-length 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names

access-list inbound permit tcp any any eq www

access-list inbound permit tcp any any eq 16080

access-list inbound permit tcp any any eq ssh

pager lines 24

mtu outside 1500

mtu inside 1500

ip address outside pppoe setroute

ip address inside 192.168.1.5 255.255.255.0

ip audit info action alarm

ip audit attack action alarm

ip local pool vpnips 192.168.1.200-192.168.1.210

pdm location 192.168.1.99 255.255.255.255 inside

pdm location 192.168.0.0 255.255.0.0 inside

pdm location 192.168.10.0 255.255.255.0 inside

pdm logging informational 100

pdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

static (inside,outside) tcp interface www 192.168.1.99 www netmask 255.255.255.255 0 0

static (inside,outside) tcp interface 16080 192.168.1.99 16080 netmask 255.255.255.255 0 0

static (inside,outside) tcp interface ssh 192.168.1.99 ssh netmask 255.255.255.255 0 0

access-group inbound in interface outside

router ospf 100

log-adj-changes

route inside 192.168.10.0 255.255.255.0 192.168.1.1 1

timeout xlate 0:05:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout sip-disconnect 0:02:00 sip-invite 0:03:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server TACACS+ max-failed-attempts 3

aaa-server TACACS+ deadtime 10

aaa-server RADIUS protocol radius

aaa-server RADIUS max-failed-attempts 3

aaa-server RADIUS deadtime 10

aaa-server LOCAL protocol local

http server enable

http 192.168.1.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server community public

snmp-server enable traps

floodguard enable

sysopt connection permit-ipsec

isakmp enable outside

telnet 192.168.0.0 255.255.0.0 inside

telnet timeout 5

ssh timeout 5

console timeout 0

vpdn group ISP request dialout pppoe

vpdn group ISP localname [email protected]

vpdn group ISP ppp authentication pap

vpdn group vpngroup client configuration address local vpnips

vpdn group vpngroup pptp echo 60

vpdn group vpngroup client authentication local

vpdn username [email protected] password *********

vpdn username *** password *********

dhcpd address 192.168.1.6-192.168.1.254 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd auto_config outside

terminal width 80

Cryptochecksum:1bc8dbe33fafd1282a7dae392efe2864

: end


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Jon Marshall Wed, 08/01/2007 - 02:44

Hi


You could do either of 2 things.


1) Enable NAT-Traversal on your ASA

2) Add the following on your pix :


fixup protocol esp-ike


This allows one IPSEC connection to run through PAT.


HTH


Jon

Actions

This Discussion