08-02-2007 02:40 AM - edited 03-14-2019 10:53 PM
Hi all,
I have 2 cme system in two locations .I want to use one cme router as gatekeeper .And limit calls between the sites to 4 g729 calls .Can any one show how can i do this defining zones?
thanks in advance
Thusharam
Solved! Go to Solution.
08-02-2007 04:07 AM
here is the sample config:
hostnames: cme1, cme2
cme1 (gwgk):
----gk config------
gatekeeper
zone local cme1 domain.com
zone local cme2 domain.com
zone prefix cme1 1...
zone prefix cme2 2...
bandwidth total zone cme1 64 (4x16kbps per call)
bandwidth total zone cme2 64
gw-type-prefix 1#* technology
arq reject-unknown-prefix
-----gw config------
interface loopback 1
ip add
h323-gateway voip interface
h323-gateway voip id cme1 ipaddr
h323-gateway voip h323-id cme1@domain.com
h323-gateway voip tech-prefix 1#
h323-gateway voip bind srcaddr
!
gateway
!
(pointing all voip call to gatekeeper)
dial-peer voice 10 voip
destination-pattern 2...
session target ras
----------------------------------
Then configure the same gateway config at cme2. replace the following:
id = cme2
h323-id = cme2@domain.com
session target = 1...
08-02-2007 02:54 AM
Hi,
You can do that but I think is really not necessary to configure GK for two sites. Just configure max-conn to 4 under dial-peer.
Hope this helps, please rate post if it does!
08-02-2007 03:49 AM
Ok.But is it cisco best practise ????
08-02-2007 03:55 AM
Yes. Best practice means doing the most with simplest configuration.
Thanks for the nice rating and good luck!
08-02-2007 04:07 AM
here is the sample config:
hostnames: cme1, cme2
cme1 (gwgk):
----gk config------
gatekeeper
zone local cme1 domain.com
zone local cme2 domain.com
zone prefix cme1 1...
zone prefix cme2 2...
bandwidth total zone cme1 64 (4x16kbps per call)
bandwidth total zone cme2 64
gw-type-prefix 1#* technology
arq reject-unknown-prefix
-----gw config------
interface loopback 1
ip add
h323-gateway voip interface
h323-gateway voip id cme1 ipaddr
h323-gateway voip h323-id cme1@domain.com
h323-gateway voip tech-prefix 1#
h323-gateway voip bind srcaddr
!
gateway
!
(pointing all voip call to gatekeeper)
dial-peer voice 10 voip
destination-pattern 2...
session target ras
----------------------------------
Then configure the same gateway config at cme2. replace the following:
id = cme2
h323-id = cme2@domain.com
session target = 1...
08-02-2007 04:20 AM
thanks . very useful...
06-08-2008 08:02 PM
I need to set up a CME to CME system with one CME as GK as well. However, I will only be working with ip addresses and will not have DNS available. Do you know what i must do in such a case?
Thanks,
06-09-2008 04:27 PM
Why is that you want to use GK with just two CMEs ?
06-09-2008 05:25 PM
This is meant for a lab just to get the concept down. Down the road may use it for larger systems.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide