cisco 3845 with NM-1CE1TE

Unanswered Question
Aug 5th, 2007

Hi dear all

i have a cisco 3845 router with nm-1ce1t1

module. the module is fine but when I pulg it to my router, it doesnt work!!

even the led on module doent turned on.

the ios version is not my problem cause i have the latest one.

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
spremkumar Sun, 08/05/2007 - 21:34

Hi

Can you post the output of show version and show diag here ?

regds

emadehsan Sun, 08/05/2007 - 22:29

yourname#terminal monitor

*Aug 6 06:21:56.171: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:01.543: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:06.911: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:12.279: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:15.975: %C3800_ENVM-3-MFAIL_OFF: There is more than one failure wi

th the Power System 1 or this Power System has been turned off.

*Aug 6 06:22:17.647: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:23.015: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:28.383: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

*Aug 6 06:22:33.755: %OIR-3-SEATED: Insert/removal failed for slot 3, check car

d seating

yourname#sh ver

Cisco IOS Software, 3800 Software (C3845-IPBASE-M), Version 12.4(4)T4, RELEASE S

OFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Thu 03-Aug-06 14:55 by kellythw

ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)

yourname uptime is 8 minutes

System returned to ROM by power-on

System image file is "flash:c3845-ipbase-mz.124-4.T4.bin"

Cisco 3845 (revision 1.0) with 222208K/39936K bytes of memory.

Processor board ID FCZ103873EQ

6 FastEthernet interfaces

2 Gigabit Ethernet interfaces

DRAM configuration is 64 bits wide with parity enabled.

479K bytes of NVRAM.

62720K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

yourname#sh diag

3845 Backplane EEPROM:

Hardware Revision : 1.0

Top Assy. Part Number : 800-23093-01

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC10341CH8

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Part Number : 73-8639-04

CLEI Code : IPME110BRA

Chassis Serial Number : FCZ103873EQ

Product (FRU) Number : CISCO3845

Version Identifier : V01

Hardware date code : 20060823

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 04 2B 41 01 00 C0 46 03 20 00 5A 35 01

0x10: 42 42 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31

0x20: 30 33 34 31 43 48 38 03 00 81 00 00 00 00 04 00

0x30: 82 49 21 BF 04 C6 8A 49 50 4D 45 31 31 30 42 52

0x40: 41 C2 8B 46 43 5A 31 30 33 38 37 33 45 51 CB 92

0x50: 43 49 53 43 4F 33 38 34 35 20 20 20 20 20 20 20

0x60: 20 20 89 56 30 31 20 83 01 32 1A 97 FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Backplane Registers

-------------------

Backplane Revision: 00BE

Power Supply Status: 0BEF

-48V PS and Env Status: FFFF

-48V Isolation Control: 0007

Backplane Cookie: 000C

ENM/Backplane FPGA Revision: 00BE

ENM/Backplane FPGA Int0 Status: FFFF

ENM/Backplane FPGA Int2 Status: 00FF

ENM/Backplane FPGA Int4 Status : EF00

ENM Interrupt Mask: 000B

ENM/BP FPGA Interrupt 4 Mask: 0040

spremkumar Sun, 08/05/2007 - 22:32

hi

Is it possible to switch off the router and insert the card ?

can you try the same and check whether the card is getting detected..

regds

emadehsan Sun, 08/05/2007 - 22:55

i have tried this issue

turned off the router

and insert the card into every slot

the result was same

laso my ios is ipbase version

spremkumar Sun, 08/05/2007 - 23:25

Hi

I did try checking out for the ios compatibility with the hardware you are using out there but i would still suggest to key in the features you require and the additional hardwars cards you are using out over there in the tool to find out the comaptible ios for your router..

http://tools.cisco.com/Support/Fusion/FusionHome.do

regds

Paolo Bevilacqua Mon, 08/06/2007 - 01:41

Hi,

The NM is not recognized in show diag. Either It has been damaged during insertion with power on, os something else is wrong.

Andyfweih Mon, 08/13/2007 - 02:59

Dear business partners & valued customers :

I am pleased to enclose it for your reference.

We can give you better price depending on the items and Qty.

Large quantity new & used Cisco and networking products that aren't

included in this catalogue. Feel free to contact us with your

requirements.

50% discount of GPL!! (Original new, 1 year warranty)

WS-C3560-24TS-S

WS-C3560-48TS-S

WS-C3560G-24TS-S

WS-C3560G-48TS-S

WS-C3750-24TS-S

WS-C3750-48TS-S

WS-C3750G-12S-S

WS-C3750G-24TS-S

WS-C3750G-24PS-S

60% discount of GPL!! (Original new, 1 year warranty)

WS-C3560-48TS-E

WS-C3560-24TS-E

WS-C3750G-24T-E

WS-C3750G-24TS-E

WS-C3750G-24PS-E

WS-C3750G-48TS-E

WS-C3750G-48PS-E

CISCO1841 $630

Looking forward to receiving your enquiries soon.

Best Regards

Andy Feng

FEDON(INT'L)DEVELOPMENT LTD

MSN:[email protected]

Email:[email protected]

Http://fweih.diytrade.com

Actions

This Discussion