08-15-2007 01:40 AM - edited 03-14-2019 01:11 AM
Hi all,
I have 1 Cisco 3825 Router with module NM-1CE1T1-PRI
And i have one line E1 connect to this
I have configed Cisco AS5300 work with E1 line and callmanager, but with 3825 i have some problem
Any one can send me config example with 3825 router to accept incoming call and forward to callmanager
Thanks alot, vote 5* for your help
08-15-2007 09:00 PM
Any one have configed Cisco Router 3825 to work with ISDN E1 line and callmanager?
Can you share your config sample?
Thanks alot
08-16-2007 12:49 AM
Let me know which protocol you want to use?
H.323 or MGCP?
08-19-2007 10:19 AM
I use H323 protocol
On my router 3825 i use "NM-1CE1T1-PRI" module
This module support E1 and T1 line
I use command "card type E1", and i can see interface from 0-30, E1 port on module is port 1/1.
But after config channel 15, i didn't find command to config voice port 1/1:D
(with E1 module, voice port is config to receive incoming call, and place out going call)
May be have some different with module NM-1CE1T1-PRI
Any one can help, thanks
08-19-2007 11:16 AM
here's a sample config from a router running H323
isdn switch-type primary-net5
controller E1 0/2/0
framing NO-CRC4
pri-group timeslots 1-31
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
no cdp enable
voice-port 0/2/0:15
dial-peer voice 1 voip
destination-pattern
session target ipv4:
dtmf-relay h245-alphanumeric
codec g711ulaw
HTH
Narayan
08-20-2007 12:29 AM
Thanks Narayan, i vote 5* for your help
I have configed ISDN E1 with AS5300
But with this module i did not see voice-port :15 to config
Do you see this problem before? May be line E1 down or i did not config right ?
I user NM-1CE1T1-PRI module, after change card type to E1, i see all channel 0-30 but can not see voice port :15
09-06-2007 03:05 AM
Hi, all
Any one configed module NM-1CE1T1-PRI for voice.
After i config controller on e1 interface, config linecode, framing, pri timeslot, I didn't see any "voice port"
I sure that linecode, framing, e1 line is ok, because i use this e1 line with AS5350 and all thing run well
May be have some problem with module NM-1CE1T1-PRI. Do this module support Voice??
Or have some problem in hardware?
Thanks for all help
09-06-2007 03:38 AM
Let me know your router is taking the pri group timeslots 1-31 command or not.If there is any lack of DSP resources it will show u
Plz check this
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_data_sheet09186a0080189f95.html
09-07-2007 08:42 PM
I use line E1, after config
"controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31 "
I see interface serial 1/0:0-1/0:30
And I config interface serial1/0:15( d channel)
"interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice modem 64
no cdp enable
!"
But after that, i did not see any voice port while type "show run"
I use software Version 12.4(13b)
09-11-2007 03:02 AM
Any one can help??
09-11-2007 03:12 AM
Do you have network-clock-select command?
And I think you should have "incoming-voice voice" instead modem 64.
--
regards,
pk
09-11-2007 09:21 PM
You can try one more command in controller E1
'clock source
09-13-2007 12:55 AM
Thanks thomasarun
I upgraded new software, new version is:
"Cisco IOS Software, 3800 Software (C3825-IPVOICEK9-M), Version 12.4(4)T8, RELEASE SOFTWARE (fc3)"
"Cisco 3825 (revision 1.0) with 226304K/35840K bytes of memory.
Processor board ID FHK0949F0LM
2 Gigabit Ethernet interfaces
31 Serial interfaces
1 Channelized E1/PRI port
4 Voice FXO interfaces
8 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
62720K bytes of ATA System CompactFlash (Read/Write)"
But after try each of: clock source external, line, external, voice port 1/0:D did not show (my E1 port is 1/0)
May be this module NM-1CE1T1-PRI have some different in configuration.
Any one can help?
Thanks
09-13-2007 02:40 AM
card type e1
Controller E1
framing
linecode
clock source
pri-group timeslots 1-31
then can u give the sh run details.
09-16-2007 06:56 PM
Thanks thomasarun
-------------
here is my 3825 configuration:
GW#sh run
Building configuration...
card type e1 1
!
ip subnet-zero
ip cef
!
no ip domain lookup
isdn switch-type primary-net5
voice-card 0
no dspfarm
!
voice service voip
allow-connections h323 to h323
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
h323
no h225 timeout keepalive
no call service stop
call start slow
!
!
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g729br8
codec preference 3 g711ulaw
!
!
!
voice class h323 1
h225 timeout tcp establish 3
telephony-service ccm-compatible
ccm-compatible
!
fax interface-type fax-mail
!
controller E1 1/0
framing NO-CRC4
clock source internal
pri-group timeslots 1-31
!
interface GigabitEthernet0/0
ip address 192.168.10.100 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
h323-gateway voip interface
h323-gateway voip h323-id h323Gateway
h323-gateway voip bind srcaddr 192.168.10.100
!
interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-4ess
isdn incoming-voice modem
isdn send-alerting
isdn sending-complete
no cdp enable
!
interface Dialer0
no ip address
!
interface Group-Async0
physical-layer async
no ip address
encapsulation ppp
dialer in-band
dialer idle-timeout 900
no group-range
!
ip default-gateway 192.168.10.1
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.10.1
!
control-plane
!
dial-peer voice 19 voip
answer-address 19..
!
dial-peer voice 9 pots
destination-pattern 9T
!
dial-peer voice 2 voip
preference 1
destination-pattern 1...
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.10.200
dtmf-relay h245-alphanumeric
no call fallback
no vad
!
dial-peer voice 1 pots
answer-address .
!
gateway
timer receive-rtp 1200
!
!
line con 0
stopbits 1
line aux 0
modem InOut
transport input all
stopbits 1
!
scheduler allocate 20000 1000
!
end
GW#
-----------------
And here is output about all module
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: NA , SN: FOC094432Q8
NAME: "One Port Channelized E1/T1/PRI with Integrated CSU on Slot 1", DESCR: "One Port Channelized E1/T1/PRI with Integrated CSU"
PID: NM-1CE1T1-PRI= , VID: 1.0, SN: FOC09360EZ8
----------
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: