cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
519
Views
0
Helpful
5
Replies

ISDN PRI Problem!

hoanghiep
Level 1
Level 1

Hi all,

I have a Cisco 2821 router with VWIC2-2MFT-E1/T1 to connect to PSTN via E1 PRI. I think that all the configurations are OK (as I had done a case before and the configurations are the same) but Layer 2 cannot go to MULTIFRAME_ESTABLISHED.

Could anyone give me some explains or instructions.

Thanks and regards,

hoanghiep

The configurations:

########################

card type e1 0 0

!

no aaa new-model

!

resource policy

!

network-clock-participate wic 0

!

isdn switch-type primary-net5

!

voice-card 0

no dspfarm

!

controller E1 0/0/0

framing NO-CRC4

pri-group timeslots 1-24 ##I have also 8 FXO ports so there're enough DSP for only 24 timeslots### (same thing for the already-running-system I mentioned above)

!

interface Serial0/0/0:15

no ip address

encapsulation ppp

isdn switch-type primary-net5

isdn incoming-voice voice

keepalive 10 3

no cdp enable

###########

show isdn status

Global ISDN Switchtype = primary-net5

ISDN Serial0/0/0:15 interface

dsl 0, interface ISDN Switchtype = primary-net5

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = AWAITING_ESTABLISHMENT

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x80FF7FFF

Number of L2 Discards = 0, L2 Session ID = 190

#############

debug isdn q921

*Aug 18 04:57:26.575: ISDN Se0/0/0:15 Q921: L2_EstablishDataLink: sending SABME

*Aug 18 04:57:26.575: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=0

*Aug 18 04:57:27.575: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=0

*Aug 18 04:57:28.575: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=0

*Aug 18 04:57:29.575: ISDN Se0/0/0:15 Q921: User TX -> SABMEp sapi=0 tei=0

5 Replies 5

Majdi Harb
Level 3
Level 3

i think u have to check from Telco side to make sure ur PRI is ready and activated from their side.

i had like this before and it was a Telco issue.

hth

/majdi

2smith
Level 1
Level 1

Hello

Have you tried changing the CRC4 in the framing - in the UK we use CRC4.

AJAZ NAWAZ
Level 5
Level 5

is this MGCP gateway?, if so do you have the full config?

Ajaz

Avner Izhar
Level 3
Level 3

Hi,

Put 'encapsulation hdlc' instead of the encapsulation ppp you have, reload and you should be fine.

HTH, Avner.

thomasarun
Level 1
Level 1

I think the linecode command is missing in controller E1

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: