cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
367
Views
5
Helpful
7
Replies

CME4.1 without CUE and Auto Responder

rsefer
Level 1
Level 1

I have CME4.1, no CUE

Outside calls from FXO are forwarded to Operator Hunt Group.

During work-hours no problem.

I is possible, during off-hours, to redirect outside calls from FXO to TCLAA? or another Responder.

Can it be automatically switched using nigth service or manually CFA?

7 Replies 7

paolo bevilacqua
Hall of Fame
Hall of Fame

Yes, you can use AA-BACD as auto-responder. If using a proper hunt-group you can define a "final" number that will take calls when all operators are logged out or not answering.

If using a shared lide, you can set CFA to TCL-AA.

In both cases you will set a voip DP in "loopback" to make the AA to take the call. This done with makeing session-target to the same address as of the router.

Hope this helps, please rate post if it does!

Thank You,

Do yo have a configuration

For which part, how do you want things to work ?

Excuse me,

I dont have any idea about how to do it?

Simply I have;

4-FXO lines

1-Operator Telephone, with 4-lines

During work-hours

Outside calls from FXO lines is forwarded to operator, then he-she forward the call to inside.

During off-hours

Operator has been already made CFA to TCLAA manually.

So Outside calls is forwarded to TCLAA.

Do you have a complete configuration

TCL-AA, Dial-peer, e-phone, ..

Ah, you want the full enchilada as they say :)

Under each fxo voice-port:

connection plar opx

config to AA-TCL, you have to adapt for your needs, read the documentation.

application

!

service aa flash:/IVR/app-b-acd-aa-2.1.2.3.tcl

paramspace english index 1

param handoff-string aa

param dial-by-extension-option 1

paramspace english language en

param max-time-vm-retry 1

param aa-pilot 333

param max-extension-length 4

paramspace english location flash:/IVR/

param welcome-prompt _bacd_welcome.au

param voice-mail 20

param max-time-call-retry 250

param service-name queue

!

service queue flash:/IVR/app-b-acd-2.1.2.2.tcl

param aa-hunt3 24

param aa-hunt4 10

param queue-manager-debugs 1

param number-of-hunt-grps 4

param aa-hunt2 23

!! Loopback DP for AA, you would CFA to 67

dial-peer voice 67 voip

description AA-BACD

service recorder

destination-pattern ^67$

session protocol sipv2

session target ipv4:192.168.234.5 <---- Router address here,preferably loopback interface

incoming called-number ^67$

dtmf-relay rtp-nte

codec g711ulaw

no vad

FINAL WARNING: You have FXO lines and during AA-BACD operation, you might have stuck calls because lack of disconnect supervision. Check that your telco (if in the US) can provide ground-start or power-denial. If not, you will need to configure tone-based disconnect.

Thank you very much,

4 port FXO is forwarded to Operator Telephone usig connection plar opx

Operator telephone has 4-lines

So the operator CFA each line (4-times)

Which is time consuming, and open to mistakes

Is there any practical way to do it?

Is there any solution for automatic forwarding at off-hours?

Hi,

No you don't need 4 lines for the operator. An ephone-dn can be made dual line so while on a call, operator will see and hear another one coming in. Beyond 2 simultaneous calls you would need to configure another ephone-dn, but usually that is not really necessary. So a single CFA is all what is needed.

Then yes there is a way to automatize night-service based on time and day (look for that the manual), but in light of the above, and the fact that it is a rigid mechanism, I do not recommend it.

Thanks for the nice rating and good luck!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: