08-20-2007 02:47 PM - edited 03-05-2019 06:00 PM
I'm having a Catalyst 6506 with a Sup1 which I'm looking to replace by a Sup32, but I'm not able to check if the Fan tray is what I need for supporting the Sup32. Is there someone which knows how to check if we have a fan tray inside, and is there different fan trays, or there is one or there is none?
if I do sh modules I get:
sh modu
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 2 Cat 6k sup 1 Enhanced QoS (Active) WS-X6K-SUP1A-2GE SAL0542DDJ7
3 16 16 port 1000mb GBIC ethernet WS-X6416-GBIC SAL0543DJBD
4 24 24 port 100FX Multi mode WS-X6324-100FX-MM SAD055005KG
5 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL0547EH4V
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 0006.d659.de28 to 0006.d659.de29 7.1 5.4(2) 7.5(0.6)HUB2 Ok
3 0007.4f6d.45b0 to 0007.4f6d.45bf 1.0 5.4(2) 7.5(0.6)HUB2 Ok
4 0002.fcbd.b288 to 0002.fcbd.b29f 3.0 5.4(2) 7.5(0.6)HUB2 Ok
5 0005.7409.7928 to 0005.7409.7957 5.0 5.4(2) 7.5(0.6)HUB2 Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- --------------- --------------- ------- -------
2 Policy Feature Card WS-F6K-PFC SAL0542DB38 1.1 Ok
2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL0541D4YB 1.2 Ok
5 Inline Power Module WS-F6K-PWR 1.0 Ok
if I do sh power, I also don't find references to the fan tray:
system power redundancy mode = redundant
system power total = 1153.32 Watts (27.46 Amps @ 42V)
system power used = 532.98 Watts (12.69 Amps @ 42V)
system power available = 620.34 Watts (14.77 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-1300W 1153.32 27.46 OK OK on
2 WS-CAC-1300W 1153.32 27.46 OK OK on
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 - - 121.80 2.90 - -
2 WS-X6K-SUP1A-2GE 121.80 2.90 121.80 2.90 on on
3 WS-X6416-GBIC 118.02 2.81 118.02 2.81 on on
4 WS-X6324-100FX-MM 63.84 1.52 63.84 1.52 on on
5 WS-X6348-RJ-45 100.38 2.39 100.38 2.39 on on
Inline Inline
Pwr-Requested Pwr-Allocated
Slot Card-Type Watts A @42V Watts A @42V
---- ------------------ ------- ------ ------- ------
5 WS-X6348-RJ-45 - - 7.14 0.17
08-20-2007 03:00 PM
Try the command 'show environment status'
08-20-2007 03:32 PM
yes, fan tray is in there.
but do we have different fantrays, or is just one type, having it is ok for Sup32, or not having it is not ok?
08-20-2007 04:01 PM
Quoting from the link below.
Supervisor Engine 32 requires the high-speed fan tray when operating in the Cisco Catalyst 6500 chassis. As such, a minimum of 2500W AC (in either 110V or 220V mode) or DC power supply is required for operation in a 6-, 9-, and 13-slot chassis.
http://www.cisco.com/en/US/products/hw/switches/ps708/prod_bulletin0900aecd801ff3ee.html
HTH
Sundar
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide