cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
823
Views
5
Helpful
7
Replies

Q on cme

user-cisco
Level 1
Level 1

hi

i want to use my 2811 gateway as cme, i downloaded 12.4.11XJ ip voice image that supports 4.1 cme, according to cme admin guide i have to install cme-basic-xxx.tar file for cme to work, the issue is that i can't find this tar file in cco, i can only find cme-gui-xxx.tar files and a zip cme 4.1 file for 12.4.11XJ, but even this it does not have cme-basic-xxx.tar file, can any one help me in this issue?

it is not restricted with 12.4.11XJ, there are other ios images that support cme but does not have cme-basic-xx.tar file. do i miss a thing here?

please help

7 Replies 7

gogasca
Level 10
Level 10

Try to enter the telephony-service command.

that file afaik contains loads and some config files for phones.

Hi,

If you download the file cme-124-11XJ.zip with your cco aacount, you will have all the the files needed for your ios version.

This is the link to the download : http://www.cisco.com/cgi-bin/Software/Tablebuild/doftp.pl?ftpfile=cisco/voice/ip-phone/ip-key/cme-124-11XJ.zip&app=Tablebuild&status=showC2A

This file will have the phone loads, cme gui, ringtones etc that you need to upload to the routers flash.

Rgds,

Jeroen

thanks jeroenhermans for ur response

actually i downlaoded it it is a zip file, but i wonder it does not contain the cme-basic-xxx.tar file?

second, should i just copy all files inside this zip to router flash?

another thing please, i downloaded (c2800nm-ipvoicek9-mz.124-15.T.bin) ios, and according to compatibilty matrix, this ios needs (cme-basic-4.1.0.0.tar) tar file, i downloaded it and extracted it into the flash, but the show flash output is ((invlaid checksum)) besides each copied file like this:

flash/term06.default.loads [invalid checksum]

flash/Readme7960-40.txt [invalid checksum]

please help?

thanks

Hi,

the cme-basic-xxx.tar file is the same as you downloaded but with a few less files.

What you downloaded has everything you need.

According to the cme compatibility matrix (http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a00805acf50.html) indeed your version of IOS needs CME 4.1

The easiest to get your gui files, ringtones etc on your router's flash is to run a small tftp server. You can download one from this site : http://tftpd32.jounin.net/

untar the cme-gui-4.1.0.1.tar to the same dir as the tftp server and start the tftp server

from your router do copy tftp flash:

follow the instructions to enter tftp server address filename etc

When this is done, upload the phoneloads you need. for instance, for the 7940/7960, upload P00308000500.bin,P00308000500.loads,P00308000500.sb2,P00308000500.sbn to the flash.

Go to configuration mode and enter telephony-service

type web admin system name admin password yourpassword

exit telephony-service and enable your http server by doing this :

ip http server

ip http authentication local

ip http path flash:

after doing this, you should be able to connect to the cme webinterface by browsing to http://routerip/cme.html

Rgds,

jeroen

thanks jeroen

is there any way to add these files at once? or i'm limited just to add them manually?

Hi,

You can add them all at once. I believe there is a command where you can tar -zxf directly from the tftp location. Don't know the exact command anymore.

Rgds,

Jeroen

The command to add them all at once is

archive tar /xtract tftp://192.168.1.1/cme-basic-4.0.0.0.tar flash:

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: