cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
314
Views
0
Helpful
1
Replies

ATM/IMA no web with one T-1 failure HELP

Shawn1
Level 1
Level 1

I have a customer with a Cisco 3640 router and a 4 ATM interfaces network module running c3640-ik9s-mz.123-14.t3.bin IOS image. The 4 T-1 ATM module is fully boated with 4 T-1's and My problem is a follows:

In the event that 1 of the 4 T-1s fails I still have layer 3 and I'm still able to SSH to the router from both the trusted and untrusted but the customer looses WEB. They simply can't surf. The can ping but not much else. When the T-1 comes back the WEB also comes back. Weird??!!

The config is as fallows:

interface ATM3/0

description Physical Interface for ##.ASXX.#####.1.ABC - Backbone T1

no ip address

no atm ilmi-keepalive

ima-group 1

scrambling-payload

!

interface ATM3/1

description Physical Interface for ##.ASXX.#####.2.ABC - Backbone T1

no ip address

no atm ilmi-keepalive

ima-group 1

scrambling-payload

!

interface ATM3/2

description Physical Interface for ##.ASXX.#####.3.ABC - Backbone T1

no ip address

no atm ilmi-keepalive

ima-group 1

scrambling-payload

!

interface ATM3/3

description Physical Interface for ##.ASXX.#####.4.ABC - Backbone T1

no ip address

no atm ilmi-keepalive

ima-group 1

scrambling-payload

!

interface ATM3/IMA1

description Primary Connector Interface for Sub-IF

no ip address

no atm ilmi-keepalive

!

interface ATM3/IMA1.1 point-to-point

description Connector Interface for ##.ASXX.#####.1.,.2.,.3.,.4..abc - Backbone T1

ip address ##.###.###.## 255.255.255.###

ip verify unicast reverse-path

no ip unreachables

ip accounting output-packets

ip nat outside

ip virtual-reassembly

atm pvc # # ### aal5snap

The some IMA interface is as follows:

router_#sh ima interface atm3/ima1

Interface ATM3/IMA1 is up

Group index is 33

Ne state is operational, failure status is noFailure

Active links bitmap 0xF

IMA Group Current Configuration:

Tx/Rx configured links bitmap 0xF/0xF

Tx/Rx minimum required links 1/1

Maximum allowed diff delay is 25ms, Tx frame length 128

Ne Tx clock mode CTC, configured timing reference link ATM3/0

Test pattern procedure is disabled

IMA Group Current Counters (time elapsed 619 seconds):

0 Ne Failures, 0 Fe Failures, 0 Unavail Secs

IMA Group Total Counters (last 24 hours):

0 Ne Failures, 0 Fe Failures, 0 Unavail Secs

IMA link Information:

Link Physical Status NearEnd Rx Status Test Status

---- --------------- ----------------- -----------

ATM3/0 up active disabled

ATM3/1 up active disabled

ATM3/2 up active disabled

ATM3/3 up active disabled

Any help would be great

1 Reply 1

purohit_810
Level 5
Level 5

ima active-minimum-links

pUT ABOVE COMMAND AND DEFINE MINIMUM LINK 1 SHOULD UP.

IMA Group Comes Down see on below URL:

http://www.cisco.com/en/US/tech/tk39/tk356/technologies_tech_note09186a0080093c93.shtml

Regards,

Dharmesh Purohit

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card