09-06-2007 09:53 AM - edited 03-14-2019 11:24 PM
Guys,
I am having a bit of a trouble here, i am able to make out going calls for all the extensions, but on an inbound call from out side on any of the PRI numbers, i get a dial tone after dialing, after which if i dial the extension number, the extension rings other wise not can any one please help me out to resolve this issue i am also attaching the config file.
09-06-2007 10:02 AM
Your DP 1 is not matching the called number:
dial-peer voice 1 pots
incoming called-number 1..
Change to what you see in "debug isdn q931" and the call will accepted.
I don't know if you have DID and if so what "dialplan-pattern" is needed under telephony-service. That is also needed to ring the extensions directly from outside.
09-06-2007 10:11 AM
thanks for ur reply i had tried using 1.. in dial peer but it did not work
i also configured dialplan patter
the DID range is from 8020100 to 8020299
09-06-2007 10:36 AM
So configure incoming called-number 8020...
You can remove the port from the incoming DP, it is not used.
and "dialplan-pattern 1 8020... extension-length 3"
As an appreciation to those providing answers, please rate useful posts using the scrollbox below!
09-06-2007 11:03 PM
i tried the paramaters mentioned still the same.
09-06-2007 11:38 PM
Then just use .. for incoming called-number in the DP that has direct-inward-dial. Or take debugs isdn q931 with term mon and place the correct number.
09-06-2007 11:51 PM
ok i ll try this tomorrow and reply abt the result
09-07-2007 12:16 AM
Hi,
put the cmd "direct-inward-dial" under your POTS dial peers this should stop the secondary dial tone, also how many digits is your service provider presenting BT present 6 by default so unless you have asked for only 3 to be presented you will need a translation pattern to change the incoming 6 digits to 3.
I hope this helps
09-07-2007 05:17 AM
Dear Anderson
the number provided by the telco is 8020222 the range i have been given is 8020100 to 299.i hav configrued the extensions starting from 100 to 135 i have arleady put direct-inward-dial. can u tell me how to do the translation.
Cheers
aamir
09-07-2007 05:36 AM
The command under telephony-service is:
dialplan-pattern 1 8020... extension-len 3
This assumes telco is sending 7 digits for called number thing that you can verify with "term mon" and "debug isdn q931".
09-07-2007 11:37 PM
Dear the following is the result of debug isdn q931
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98388
Exclusive, Channel 8
Progress Ind i = 0x8483 - Origination address is non-ISDN
Calling Party Number i = 0x2183, '048850447'
Plan:ISDN, Type:National
Called Party Number i = 0x81, '0122'
Plan:ISDN, Type:Unknown
Sep 8 07:20:15.386: ISDN Se0/0/1:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x9
D52
Channel ID i = 0xA98388
Exclusive, Channel 8
Sep 8 07:20:15.386: ISDN Se0/0/1:15 Q931: TX -> CONNECT pd = 8 callref = 0x9D5
2
Sep 8 07:20:15.846: ISDN Se0/0/1:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0
x1D52
Sep 8 07:20:15.846: ISDN Se0/0/1:15 **ERROR**: call_progress: DEV_CONNECTED VOI
CE ERROR: Bearer capability not available(0x3A): b channel 7 call id 0xF8
can u please go throug and help me
09-08-2007 01:50 AM
Telco is passing four digits. Use
"incoming called-number 0..." and
"dialplan-pattern 1 0... extension-length 3".
09-09-2007 08:18 AM
thanks my issue is resloved and i have rated ur post
09-09-2007 08:30 AM
Thanks for the nice rating and good luck!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: