HWIC-1FE in 2811 - still not seeing it

Unanswered Question
Sep 12th, 2007
User Badges:

I upgraded the image to c2800nm-entservicesk9-mz.124-17.bin and reloaded it but it gives a new error message. This is the boot text I get:



Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0003E7 0X003DA000 C2811 Mainboard

0X000021B8 Onboard USB

0X002C29F0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X008AFBA8


If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 10Mb.

Using 3 percent iomem. [10Mb/256Mb]


%GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53APort Statistics for unclassified packets is not turned on.


%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.


program load complete, entry point: 0x8000f000, size: 0x223b98c

Self decompressing the image : ######################################################################## [OK]



Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0003E7 0X00473800 C2811 Mainboard

0X000021B8 Onboard USB

0X002C29F0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X009493A8


If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 10Mb.

Using 3 percent iomem. [10Mb/256Mb]


Cisco IOS Software, 2800 Software (C2800NM-ENTSERVICESK9-M), Version 12.4(17), RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Fri 07-Sep-07 16:45 by prod_rel_team

Image text-base: 0x40094FC0, data-base: 0x427E8910


Cisco 2811 (revision 49.46) with 251904K/10240K bytes of memory.

Processor board ID FTX1125A62K

2 FastEthernet interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)




Press RETURN to get started!



*Sep 12 14:37:11.051: %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53A

*Sep 12 14:37:14.551: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up

*Sep 12 14:37:14.555: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

*Sep 12 14:37:14.555: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

*Sep 12 14:37:15.911: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

*Sep 12 14:37:15.911: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

*Sep 12 14:37:16.347: %SYS-5-CONFIG_I: Configured from memory by console

*Sep 12 14:37:16.639: %SYS-5-RESTART: System restarted --

Cisco IOS Software, 2800 Software (C2800NM-ENTSERVICESK9-M), Version 12.4(17), RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Fri 07-Sep-07 16:45 by prod_rel_team

*Sep 12 14:37:16.643: %SNMP-5-COLDSTART: SNMP agent on host dod2811 is undergoing a cold start

*Sep 12 14:37:18.219: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down



I dont see the card when I do show interfaces. At first before I upgraded the image I tried slot 0, then noticed that this was a voice only slot so I tried slot 1 and then slot 3 which it is in now.


Is there maybe a way to clear the slot configuration?


Any suggestions?

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
a.alekseev Wed, 09/12/2007 - 06:54
User Badges:
  • Gold, 750 points or more

You should use 12.4 T-train.

12.4.15T for example

Actions

This Discussion