6509 error

Unanswered Question
Sep 15th, 2007

Hi,

Anyone seen this:

Sep 15 07:50:07.202 UTC: %MLSCEF-SP-2-FIB_SSRAM_WRITE_INCONSISTENCY: FIB SSRAM Mismatch for Index: 16386

Expected: 4000 , Hardware: 40A8

BR,

Bjornarsb

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Edison Ortiz Sat, 09/15/2007 - 12:00

Let's see

show mls cef hardware

You may have to contact TAC and have the SP DRAM replaced.

bjornarsb Sun, 09/16/2007 - 06:02

#sh mls cef hardware ?

module Show for module

| Output modifiers

sw96aq#sh mls cef hardware

CEF TCAM v2:

Size:

65536 rows/device, 2 device(s), 131072 total rows

32 entries/mask-block

8192 total blocks (32b wide)

0 - 4095 upper blocks, 4096 - 8191 lower blocks

1179648 s/w table memory

Used blocks:

Upper bank:

43 IP ucast

0 IPX

2 IP mcast

Lower bank:

0 IP ucast

0 IPX

0 IP mcast

Max:

51 IP ucast

0 IPX

2 IP mcast

Free blocks (non-contiguous range):

22 - 4095 upper blocks, 4096 - 8191 lower blocks

Options:

sanity check: on

sanity interval: 301 seconds

redistribution: off

redistribution interval: 120 seconds

redistribution threshold: 10

compression: on

compression interval: 31 seconds

serialization: on

serialization interval: 16 seconds

recovery: on

recovery interval: 3 seconds

bank balancing: off

bank differential limit: 5

rpf mode: off

tcam shadowing: on

Background Task statistics:

sanity check count: 0000000000129642

Consistency check count: 0000000001252770

Consistency check errors- TCAM: 0000000000000000

Consistency check errors- SSRAM:0000000691786340

block redistribute count: 0000000000000000

IP ucast serialize count: 0000000000222322

IP mcast serialize count: 0000000000000000

IP ucast recover count: 0000000000000000

IP mcast recover count: 0000000000000000

block compress count: 0000000000041128

IP ucast [32]: 0000000000002132

IP ucast [30]: 0000000000000003

IP ucast [24]: 0000000000000080

Hardware switching status:

ip switching: on

ipx switching: off

Edison Ortiz Sun, 09/16/2007 - 08:01

I don't see anything wrong at the CEF table.

What IOS version and Supervisor module are you running ?

bjornarsb Sun, 09/16/2007 - 08:21

Hi again,

#sh ver

Cisco Internetwork Operating System Software

IOS (tm) s222_rp Software (s222_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Thu 23-Mar-06 16:59 by tinhuang

Image text-base: 0x40101040, data-base: 0x42C38000

ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)

BOOTLDR: s222_rp Software (s222_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)

sw96aq uptime is 1 year, 12 weeks, 2 days, 17 hours, 54 minutes

Time since sw96aq switched to active is 1 year, 12 weeks, 2 days, 17 hours, 56 m inutes

System returned to ROM by power-on (SP by power-on)

System restarted at 22:23:15 UTC Wed Jun 21 2006

System image file is "disk0:s222-adventerprisek9_wan-mz.122-18.SXF4.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

cisco WS-C6509 (R7000) processor (revision 3.0) with 458752K/65536K bytes of memory.

Processor board ID TBP06160220

R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache

Last reset from power-on

SuperLAT software (copyright 1990 by Meridian Technology Corp).

X.25 software, Version 3.0.0.

Bridging software.

TN3270 Emulation software.

28 Virtual Ethernet/IEEE 802.3 interfaces

24 FastEthernet/IEEE 802.3 interfaces

58 Gigabit Ethernet/IEEE 802.3 interfaces

381K bytes of non-volatile configuration memory.

16384K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE SAL06240XFY

2 24 24 port 100mb MTRJ ethernet WS-X6224-100FX-MT SAD03080079

4 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL062106CA

6 48 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-TX SAL09422XQ4

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0006.d65b.6e08 to 0006.d65b.6e09 3.7 7.1(1) 12.2(18)SXF4 Ok

2 00d0.bb09.1b60 to 00d0.bb09.1b77 1.2 4.2(0.24)VAI 8.5(0.46)RFW Ok

4 0009.1267.8e90 to 0009.1267.8e97 2.1 5.4(2) 8.5(0.46)RFW Ok

6 0015.f952.8390 to 0015.f952.83bf 1.1 8.4(1) 8.5(0.46)RFW Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 SAL06240Z8D 3.2 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06230U51 2.3 Ok

Mod Online Diag Status

---- -------------------

1 Pass

2 Pass

4 Pass

6 Pass

Edison Ortiz Sun, 09/16/2007 - 11:42

Open a TAC case and have the SP DRAM replaced.

Per your CEF output

Consistency check errors- SSRAM:0000000691786340

This count should be zero. Good luck !

The closest match I could find was this.....

%MLSCEF-2-FIB_SSRAM_WRITE_INCONSISTENCY : FIB SSRAM Mismatch for Index: [dec]

Expected: [hex], Hardware: [hex]

Explanation A problem occurred when the system attempted to write the FIB SSRAM.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the information that you have gathered. Attach the following information to your case in nonzipped, plain-text (.txt) format: the output of the show logging and show tech-support commands and your pertinent troubleshooting logs.

emadehsan Sat, 09/15/2007 - 12:40

hi thank you for your reply

but as i said the sup wont get turn on.it remain dead! so i have no access to console

thank you

Edison Ortiz Sat, 09/15/2007 - 12:45

You never said that :)

If that's the case, you need to replace the Sup. Open a TAC case.

emadehsan Sat, 09/15/2007 - 20:45

i have two SUP2, but none of them works!

wehn i turn the power on , the status led flashe once, and then nothing else!

Edison Ortiz Sun, 09/16/2007 - 07:56

Are you the original poster of this thread ? If not, please open a new thread to avoid any confusion.

Actions

This Discussion