Configure E1 Controller Card in cisco 2801 Router

Unanswered Question
Oct 4th, 2007
User Badges:

Connectivity from india to uk end through lease line. (Lease line is woring fine). Ineed to connect the Alcatel pbx in both for voice connectivity. I need your help in configuring e1 controller card.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
kumaranchn Fri, 10/05/2007 - 02:40
User Badges:

The link is not working. If you need he configuration I will send it.

royalblues Fri, 10/05/2007 - 04:01
User Badges:
  • Green, 3000 points or more

Sorry i could not understand..


Are you saying you were able to configure the controller or would you be sending the configurations that need to be done?


Narayan

kumaranchn Fri, 10/05/2007 - 08:02
User Badges:

We are having 2 offices conectivity from India to UK through lease line connectivity. Through Alcatel Pbx line we have to configure the Voice card ie (if we dial 84) it should be connected to uk directly) through E1 Controller card. If you need the configuration I will send it.

paolo bevilacqua Fri, 10/05/2007 - 08:46
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Is not that we need the configuration. Please describe the problem you are facing.

kumaranchn Fri, 10/05/2007 - 18:33
User Badges:

The Issue is the E1 Controller card is still down (ie Status is up ; Protocol is down). For more details I have attached the configuration of Sh run,Sh ip int brief & Sh version).



Attachment: 
paolo bevilacqua Fri, 10/05/2007 - 18:58
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Are you positive about setting no-crc4 and linecode ami (that's uncommon) as confirmed by telco ? Please check output of "show controllers e1" and "show interface serial x/y".

kumaranchn Fri, 10/05/2007 - 22:40
User Badges:

if I configured framing cr4 the contoller E1 is getting down. If you are willing to access the router pls reply I will give my mobile number

paolo bevilacqua Sat, 10/06/2007 - 03:01
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

I don't need to access the router. You would need to post here output of the two commands I mentioned above.

paolo bevilacqua Sat, 10/06/2007 - 07:59
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Are we talking about the data circuit to UK? If so I think you have configured for 1 timeslots whereby you need 30 (or 31), check with SP.


so enter:


interface Serial0/2/0:1

shutdown

controller e1 0/2/0

shutdown

no channel-group 1 timeslots 30

channel-group 1 timeslots 1-31

no shutdown


interface Serial0/2/0:1

no shutdown

ip address ...


instead if you want to do voice with this device, you are lacking the DSP resources and a voice version of IOS on it. The you should move to unified voice the discussion.


In any case you need to configure the following to fix the slip on the circuit.


network-clock-participate wic 2

network-clock-select 5 e1 2/0



kumaranchn Mon, 10/08/2007 - 01:51
User Badges:

I have attached the configuration of router.

Now I need to get the E1 controller card to become up (ie Protocol). I have to connect from router to Alcatel Exchange.



Attachment: 
paolo bevilacqua Mon, 10/08/2007 - 02:00
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

interface serial 0/2/0:1

shutdown


controller E1 0/2/0

shutdown

no channel-group 1 timeslots 30

primary-group

no shutdown


int serial 0/2/0:15

isdn protocol-emulate network


Note: you need PVDM2-32 module inserted in the router (or smaller if you plan for less that 32 calls) to do this.


Please post other voice related questions to "unified communications" forum that you can locate on the left linkbar.


hope this helps, please rate post if it does!




Actions

This Discussion