cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
974
Views
0
Helpful
2
Replies

Error while Saving configuration on ASA

palukuri77
Level 1
Level 1

Hi,

I do get the following error while saving the configuration to memory on my ASA box.

HCL-BMB-ASA-PRI# wr mem

Building configuration...

Cryptochecksum: 42bceaba 27adb265 edcb9fbd 60a1761e

%Error opening disk0:/.private/startup-config (File or directory already in use)

Error executing command

[FAILED]

show version is as follows:

HCL-BMB-ASA-PRI# sh vers

Cisco Adaptive Security Appliance Software Version 7.0(6)

Device Manager Version 5.0(6)

Compiled on Tue 22-Aug-06 13:22 by builders

System image file is "disk0:/asa706-k8.bin"

Config file at boot was "startup-config"

HCL-BMB-ASA-PRI up 38 days 21 hours

failover cluster up 38 days 22 hours

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash M50FW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : ☻CNlite-MC-Boot-Cisco-1.2

SSL/IKE microcode: ♥CNlite-MC-IPSEC-Admin-3.03

IPSec microcode : ☺CNlite-MC-IPSECm-MAIN-2.04

0: Ext: Ethernet0/0 : address is 001b.2a34.e6f6, irq 9

1: Ext: Ethernet0/1 : address is 001b.2a34.e6f7, irq 9

2: Ext: Ethernet0/2 : address is 001b.2a34.e6f8, irq 9

3: Ext: Ethernet0/3 : address is 001b.2a34.e6f9, irq 9

4: Ext: Management0/0 : address is 001b.2a34.e6fa, irq 11

5: Int: Not licensed : irq 11

6: Int: Not licensed : irq 5

Licensed features for this platform:

Maximum Physical Interfaces : Unlimited

Maximum VLANs : 25

Inside Hosts : Unlimited

Failover : Active/Standby

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 0

GTP/GPRS : Disabled

VPN Peers : 150

This platform has an ASA 5510 Security Plus license.

Serial Number: JMX1129L0VH

Running Activation Key: 0x46186153 0x1837dcd1 0x00d25d44 0xa8e47044 0x4b142883

Configuration register is 0x1

Configuration last modified by enable_15 at 12:53:21.573 IST Tue Oct 9 2007

Please help me asap!!!

Regards,

Subhash.

2 Replies 2

1cmerchant
Level 1
Level 1

You probably need to call TAC to get this resolved, but in the meantime you could write the configuration to a tftp server. That way at least you'll have a copy of the configuration in case the device goes down.

Use the 'tftp-server' command to specify the interface and IP address of the tftp server, and then a 'write net' command to actually write the config to it.

Hi,

Thanks for your response. I've the config and also failover ASA working. Opened a TAC case but just thought someone would have faced a similar issue and could throw some light on this.

Regards,

Subhash.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: