6506-e - RME Error

Unanswered Question
Oct 22nd, 2007
User Badges:

While trying to pull config for a 6506e get this error:CM0056 Config fetch failed for g0ghq3esw1 Cause: CM0204 Could not create DeviceContext for 17118 Cause: CM0206 Could not get the config transport implementation for 10.160.8.29 Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.


What updates do I need?


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Joe Clarke Tue, 10/23/2007 - 08:03
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

What is the sysObjectID from this device? You can find that under Device Center > SNMP Walk. Just walk sysObjectID.

rice.randy Thu, 10/25/2007 - 10:36
User Badges:

I just noticed that no configs for my 6504-e's are pulling. What updates do I need to to for CW to pull.

CM 4.0

DFM 2.0

IPM 2.6

RME 4.0

If updates are required, what order are they to be installed?

Joe Clarke Thu, 10/25/2007 - 11:04
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

These are not complete versions. What is the exact version of RME you have, plus, what is the sysObjectID of this switch?

rice.randy Fri, 10/26/2007 - 04:18
User Badges:

RME - 4.0.5

SysObjectID - RFC1213-MIB::sysObjectID.0 = OID: CISCO-SMI::ciscoProducts.657

Joe Clarke Sun, 10/28/2007 - 13:53
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

Support for this switch is available in Cat6000IOS package version 6.1. This package can be downloaded via the Common Services > Software Center > Device Update interface.

rice.randy Mon, 10/29/2007 - 06:38
User Badges:

While installing CAT6000ios GOT this error:

Cat6000IOS


WARNING : Cat6000IOS(6.1):Consistency check failed for base package SharedInventoryCatIOS


ERROR: Error while installing (SharedNetshowSC): D:appsCSCOpx emppsuinstall

meSharedNetshowSC.zip cannot be installed because, the current mdf version:1.12 is LESS THAN the minimum required mdf version:1.16

Where do I fin MDF 1.16?

Joe Clarke Mon, 10/29/2007 - 06:59
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

The MDF is found by selecting Common Services in addition to RME when performing the Device Update. Select all available updates.

rice.randy Mon, 10/29/2007 - 07:44
User Badges:

For Product(s) : Resource Manager Essentials


Install Invoked by user : admin


The Package(s) Selected for Install :

I installed MDF update and still get this message while trying to install CAT6000IOS package:



LibCommon


ERROR: Error while installing (LibCommon): C:psu_download

meLibCommon.zip cannot be installed because, the current mdf version:1.12 is LESS THAN the minimum required mdf version:1.19


Joe Clarke Mon, 10/29/2007 - 07:49
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

You must not have installed the MDF correctly. The current latest version is 1.21. This time, select just Common Services, pick the MDF 1.21 update, and install it. That should prompt a daemon restart. When you're able to login again, then install the RME updates.

rice.randy Mon, 10/29/2007 - 07:57
User Badges:

When I select Common Services and go get the download I get :


All the available package(s) at source location are already installed.



Dosen't this mean that the current MDF is already installed?>

Joe Clarke Mon, 10/29/2007 - 07:59
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

If you click on the CiscoWorks Common Services link under Device Update, what do you see?

rice.randy Mon, 10/29/2007 - 08:08
User Badges:

I select Common Services,

I click "Check for Updates"

I get the source location display,

I select Cisco.com,

I enter my CCO info,

I click next, then I get :


All the available package(s) at source location are already installed.

Joe Clarke Mon, 10/29/2007 - 08:10
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

No, just click the hyperlink "CiscoWorks Common Services" under Common Services > Software Center > Device Update.

rice.randy Mon, 10/29/2007 - 08:13
User Badges:

Package Map

Filter Source: Package Name Version

Showing 1-1 of 1 records

Package Name Version Description

1. Mdf 1.12 MDF Package


Joe Clarke Mon, 10/29/2007 - 08:18
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

Try restarting dmgtd, then see if the MDF version changes (assuming it was able to apply from one of your previous attempts). If not, you will need to download the MDF 1.21 update manually from http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-cd-one , then install it using NMSROOT\bin\PSUCli.bat.

Actions

This Discussion