10-30-2007 05:45 AM - edited 03-03-2019 05:33 AM
Hi,
How Can I do "default route" under router eigrp command. I mean that how can stub router send unkown packet to hub router ?
because stub router connect internet via hub router.
Thank You
10-30-2007 07:18 AM
You can 'redistribute static' under EIGRP in your hub router. That will put the 0.0.0.0/0 route into EIGRP and pass to neighbors.
HTH and please rate.
10-30-2007 07:23 AM
But I dont want use any static parameter. Everthing must be dynamic. I cant find related to default route under router eigrp command.
not ip default-network and ip route
10-30-2007 07:30 AM
What do you mean by dynamic? In one of your devices you already have a static route pointing to the internet right? Just redistribute that into EIGRP. You remote routers will then have a default route learned via EIGRP.
10-30-2007 07:36 AM
I mean that just use eigrp, not static paremeter.
Hub and spoke can communicate each other. But how can spoke router know unknown packet (Internet). It must query to hub router. Because It just go to via hub router access internet.
thank you
10-30-2007 07:41 AM
The spoke looks at its local routing table. If the route for a certain prefix exists it goes that direction. If there is no SPECIFIC route in the routing table, it will use the default route. The spoke router does not query the hub router, however the spoke router will route traffic to the hub router (to get to the internet for example).
HTH and please rate.
10-30-2007 07:45 AM
How Can I do it? Which commands must be under router eigrp ?
10-30-2007 07:51 AM
ROUTER(config)# router eigrp 1
ROUTER(config-router)# redistribute static
This will redistribute all static routes you have on the this router. If you need to prevent some static routers from being redistributed into EIGRP, you can use a route-map.
HTH and please rate.
10-30-2007 07:43 AM
The spoke looks at its local routing table. If the route for a certain prefix exists it goes that direction. If there is no SPECIFIC route in the routing table, it will use the default route. The spoke router does not query the hub router, however the spoke router will route traffic to the hub router (to get to the internet for example).
HTH and please rate.
10-30-2007 07:55 AM
Do you have a default route in your hub router? Where does it come from? If it already in EIGRP, then you are home and dry. If it comes from another protocol, RIP for example, then redistribute it into EIGRP.
Otherwise you will have to create one as a static and re-distribute it into EIGRP. In any case, these default routes have to go somewhere once they get into the hub.
Kevin Dorrell
Luxembourg
10-30-2007 08:07 AM
all of previous configuration are static. yes, I have it. I wanna use eigrp. all of paremeter must be under eigrp. not redistribute, default-network, default-gateway.
I cant find about it on cisco site.
10-30-2007 08:12 AM
You are using EIGRP. You can't have all the internet routes in EIGRP so you use the default route. To get the default route into EIGRP, you redistribute your static route pointing to the internet into EIGRP.
10-30-2007 08:25 AM
10-30-2007 08:31 AM
Thanks for the diagram. Does the DSL-R run EIGRP? Is that a router or something like a DSL modem?
10-30-2007 08:32 AM
No, Dsl doesnt run eigrp. Just Hub and spokes
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide