Level 3 Communication Interoperability Issue

Unanswered Question
Nov 6th, 2007
User Badges:

I need to work with interoperability between Cisco AS5300XM and Level 3 over VoIP. But need ideas about the Cisco equipment setup. Level 3 said "you need E.164 numbering plan and check the Call-ID" .

About the E.164 insert the symbol "+" plus the 11 digit 1+area code+number


Please let me know any ideas


thanks


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
paolo bevilacqua Tue, 11/06/2007 - 12:01
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,


you can use a translation-rule like:


voice translation-profile e164

translate called 100


voice translation-rule 100

rule 1 /^1/ /+1/


dial-peer voice 33 voip

destination-pattern 1[2-9][0-8][0-9][2-9]......

translation-profile outgoing e164


That will add the required + for US domestic calls. Repeat in other DPs as necessary for other destinations.


You may even try without the +, just use 011 for example. Chances are it will work anyway :)


Hope this helps, please rate post if it does!




tracity-noc Tue, 11/06/2007 - 12:56
User Badges:

Hi

thanks for your help

I used the following setup and don't work


For Incoming

dial-peer voice 222 pots

destination-pattern +T

port 1/0:D

prefix 1



For Outbound

voice translation-profile e164

translate called 1


translation-rule 1

Rule 1 ^1 +1



dial-peer voice 203 voip

translation-profile outgoing e164

destination-pattern 1.......... (11 digit)

session protocol sipv2

session target ipv4:x.x.x.x:5060 (IP Level3)

session transport udp

dtmf-relay rtp-nte

clid network-number +xxxxxxxxxx (my number)




My equipment is

Cisco AS5350XM

Version 12.4(11)T


thanks

Erick

paolo bevilacqua Tue, 11/06/2007 - 13:57
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,


please configure "voice translation-rule 1" and not "translation-rule 1" as these are different things.

Then when checking, please enable "debug ccsip message" and "term mon", in case of problems you can post the output here.


Note the reason I made an example with a more complicated destination-pattern than just 1 followed by 10 dots, it's because it enforces the NANP and prevents user misdialing. That is always a good thing in telephony.


Also note your DP 222 for inbound seems too relaxed in accepting everything and just sending out.

tracity-noc Tue, 11/06/2007 - 16:44
User Badges:

Hi,


We tried several calls to Level 3 equipment , the signaling passed well but not the audio


Another thing if you can help me with understanding this call-id , this is the string that they are requesting us to send to generate call to us ( Level 3 to our equipment)


Example Call-Ids:


[email protected]

[email protected]



I get this for the Cisco box (AS5350XM)


Nov 6 18:31:52.550: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:

Sent:

INVITE sip:[email protected]:5060 SIP/2.0

Via: SIP/2.0/UDP 190.7.193.85:5060;branch=z9hG4bK1B04BD

Remote-Party-ID: ;party=calling;screen=yes;privacy=off

From: ;tag=F3098510-1337

To:

Date: Tue, 06 Nov 2007 18:31:52 GMT

Call-ID: [email protected]

Supported: 100rel,timer,resource-priority,replaces

Min-SE: 1800

Cisco-Guid: 1626595571-2345472476-2173108246-2641290602

User-Agent: Cisco-SIPGateway/IOS-12.x

Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER

CSeq: 101 INVITE

Max-Forwards: 70

Timestamp: 1194373912

Contact:

Expires: 180

Allow-Events: telephone-event

Content-Type: application/sdp

Content-Disposition: session;handling=required

Content-Length: 294


v=0

o=CiscoSystemsSIP-GW-UserAgent 3437 4571 IN IP4 190.7.193.85

s=SIP Call

c=IN IP4 190.7.193.85

t=0 0

m=audio 18244 RTP/AVP 18 101 19

c=IN IP4 190.7.193.85

a=rtpmap:18 G729/8000

a=fmtp:18 annexb=no

a=rtpmap:101 telephone-event/8000

a=fmtp:101 0-16

a=rtpmap:19 CN/8000

a=ptime:20


Nov 6 18:31:52.666: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:

Received:

SIP/2.0 100 Trying

Via: SIP/2.0/UDP 190.7.193.85:5060;branch=z9hG4bK1B04BD

From: ;tag=F3098510-1337

To:

Call-ID: [email protected]

CSeq: 101 INVITE

Content-Length: 0




Nov 6 18:31:55.462: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:

Received:

SIP/2.0 183 Session Progress

Via: SIP/2.0/UDP 190.7.193.85:5060;branch=z9hG4bK1B04BD

From: ;tag=F3098510-1337

To: ;tag=VPST50603522629633

Call-ID: [email protected]

CSeq: 101 INVITE

Contact:

MIME-Version: 1.0

Content-Type: multipart/mixed;boundary=level3-viper-boundary

Content-Length: 392


--level3-viper-boundary

Content-Type: application/sdp


v=0

o=- 1194395489 1194395490 IN IP4 209.247.5.45

s=-

c=IN IP4 209.247.5.45

t=0 0

m=audio 60238 RTP/AVP 18 101

a=rtpmap:101 telephone-event/8000

a=fmtp:101 0-16

a=ptime:20

--level3-viper-boundary

Content-Type: application/isup;version=ansi

Content-Disposition: session;handling=optional







Best Regards

paolo bevilacqua Wed, 11/07/2007 - 08:28
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,


do you have any FW or NAT between the AS5300 and the internet ?


I can't quite understand the call-id issue, normall the call-id is dynamically generated, for call generated toward you what matters is the called number more than anything else.


Actions

This Discussion