×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Trouble with 2821 and VIC2-4FXO

Answered Question
Nov 6th, 2007
User Badges:

I have a 2821 with a VWIC2-1MFT-T1/E1= and a VIC2-4FXO. I have my T1 working inbound and outbound but cannot get inbound calls working on the FXO ports. The call rings once, then goes to dial tone. The follow error is received.


*Nov 6 23:06:23.822: //-1/xxxxxxxxxxxx/RXRULE/regxrule_get_profile_from_trunkgroup_internal: Voice port 0x450E38CC does not belong to any trunk group

*Nov 6 23:06:23.826: //-1/BA99D137800E/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x455F7A44; count=1

*Nov 6 23:06:23.826: //-1/BA99D137800E/RXRULE/regxrule_get_profile_from_dialpeer_internal: Error: Invalid input peer_tag=0 direction=incoming

*Nov 6 23:06:23.826: //-1/BA99D137800E/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x455F7A44; count=0


I am not sure what the inbound digits are on that line so do I need to create a catch all dial-peer and if so how do I do that?


Thanks in advance.

Adam

Correct Answer by allan.thomas about 9 years 9 months ago

Simply create a dial-peer with a session target for your CallManager with destination pattern of the opx number. For example.


voice-port 0/2/0

trunk-group VIC2-4FXO

connection plar opx 6750

caller-id enable

!

dial-peer voice 1000 voip

description *** CallManager Pattern ***

preference 1

destination-pattern 6...

translate-outgoing calling 1

voice-class codec 1

voice-class h323 1

session target ipv4:192.168.1.1

dtmf-relay h245-alphanumeric

no vad

!

dial-peer voice 1001 voip

description *** CallManager Pattern ***

preference 2

destination-pattern 6...

translate-outgoing calling 1

voice-class codec 1

session target ipv4:192.168.1.2

dtmf-relay h245-alphanumeric

no vad

!

Regards

Allan.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
paolo bevilacqua Tue, 11/06/2007 - 15:13
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,


this would be your catch-all incoming DP to avoid secondary dialtone:


dial-peer voice 111 pots

incoming called-number ...

direct-inward-dial


and this is how you group lines for outgoing, ad direct inbound:


voice-port X/0

trunk-group pstn

connection plar opx 222


voice-port X/1

trunk-group pstn

connection plar opx 222


dial-peer voice 222 pots

destination-pattern 9T

trunkgroup pstn


Hope this helps, please rate post if it does!




ahab Tue, 11/06/2007 - 15:58
User Badges:

Thanks! My goal is to use the T1 for all outbound calls, while accepting calls from the FXOs and the T1.

The following...

voice-port 0/1/0

trunk-group pstn

connection plar opx 222


got rid of the secondary dialtone.

How do I take calls from just that FXO port and send to a device within CCM? I am used to using the destination-pattern 5... (example) to send the call and then using a translation pattern to mp the incoming digets to an extension.


Thanks again!

Adam

Correct Answer
allan.thomas Tue, 11/06/2007 - 16:05
User Badges:
  • Blue, 1500 points or more

Simply create a dial-peer with a session target for your CallManager with destination pattern of the opx number. For example.


voice-port 0/2/0

trunk-group VIC2-4FXO

connection plar opx 6750

caller-id enable

!

dial-peer voice 1000 voip

description *** CallManager Pattern ***

preference 1

destination-pattern 6...

translate-outgoing calling 1

voice-class codec 1

voice-class h323 1

session target ipv4:192.168.1.1

dtmf-relay h245-alphanumeric

no vad

!

dial-peer voice 1001 voip

description *** CallManager Pattern ***

preference 2

destination-pattern 6...

translate-outgoing calling 1

voice-class codec 1

session target ipv4:192.168.1.2

dtmf-relay h245-alphanumeric

no vad

!

Regards

Allan.

ahab Tue, 11/06/2007 - 16:27
User Badges:

Thats it, I am all set. Thanks guys

Actions

This Discussion