×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Cisco View LMS 2.6 - Unsopported Card

Answered Question
Nov 7th, 2007
User Badges:

Hi folks!


I have a Cisco 7600 with 7600-sip-600 and 7600-sip-400 cards.

I see theese cards on CiscoView chassis,

but I cannot see the subslot. It told "UNSUPPORTED CARD"


The card are:


NAME: "SPA in subslot 3/0", DESCR: "1-port 10 Gigabit Ethernet Shared Port Adapter XFP based"

PID: SPA-1XTENGE-XFP , VID: V02, SN: JAB1025030A



NAME: "SPA in subslot 4/0", DESCR: "1-port 10 Gigabit Ethernet Shared Port Adapter XFP based"

PID: SPA-1XTENGE-XFP , VID: V02, SN: JAB1024050P


I download the latest package of Cat6000IOS.cv50.v28-0

and the readme says:


SHARED PORT ADAPTERS SUPPORTED BY 7600-SIP-600 MODULE

* Nil


NIL what mean?


Are theese cards submodule supported by CiscoView 6.1.5?


Thanks a lot to all for any answer;)

Leonardo

Correct Answer by Joe Clarke about 9 years 9 months ago

See the prerequisites for these modules in the CiscoView package notes:


* SPA modules of 7600-SIP-X00 and 7600-SSC-400 are partially supported in

12.2(18)SX series IOS releases. Full support is extended only by 12.2(33)SRA release.

Please note that this image should have c7600-fpd-pkg.122-33.SRA.pkg to be installed

in the device for SNMP to work properly. This FPD package can be downloaded from

http://www.cisco.com/cgi-bin/Software/Tablebuild/doftp.pl?ftpfile=swc/esd/01/268437593/contract/c7600-fpd-pkg.122-33.SRA.pkg&app=SWSearch&status=showC2A


That said, the SPA-1XTENGE-XFP sub-modules are not supported in CiscoView yet. They are listed under "UNSUPPORTED HARDWARE IN THIS RELEASE" section of the package readme.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Joe Clarke Wed, 11/07/2007 - 11:36
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    Founding Member

See the prerequisites for these modules in the CiscoView package notes:


* SPA modules of 7600-SIP-X00 and 7600-SSC-400 are partially supported in

12.2(18)SX series IOS releases. Full support is extended only by 12.2(33)SRA release.

Please note that this image should have c7600-fpd-pkg.122-33.SRA.pkg to be installed

in the device for SNMP to work properly. This FPD package can be downloaded from

http://www.cisco.com/cgi-bin/Software/Tablebuild/doftp.pl?ftpfile=swc/esd/01/268437593/contract/c7600-fpd-pkg.122-33.SRA.pkg&app=SWSearch&status=showC2A


That said, the SPA-1XTENGE-XFP sub-modules are not supported in CiscoView yet. They are listed under "UNSUPPORTED HARDWARE IN THIS RELEASE" section of the package readme.

Actions

This Discussion