No, this site is using all BRI.

Here is the output from debug isdn q931. The first is for a call to cell phone and the second is a call to a land line.

2d16h: ISDN BR2/0/1 Q931: Applying typeplan for sw-type 0xC is 0x0 0x0, Calling

num 3025

2d16h: ISDN BR2/0/1 Q931: TX -> SETUP pd = 8 callref = 0x04

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x81

Preferred, B1

Keypad Facility i = '18045551212'

Calling Party Number i = 0x0080, '3025'

Plan:Unknown, Type:Unknown

2d16h: ISDN BR2/0/1 Q931: RX <- CALL_PROC pd = 8 callref = 0x84

Channel ID i = 0x89

Exclusive, B1

Locking Shift to Codeset 5

Codeset 5 IE 0x2A i = 0x80880B, '18045551212', 0x8001098001148001148001

14

2d16h: ISDN BR2/0/1 Q931: RX <- INFORMATION pd = 8 callref = 0x84

Called Party Number i = 0x80, '18043477539'

Plan:Unknown, Type:Unknown

Locking Shift to Codeset 5

Codeset 5 IE 0x2A i = 0x808300800114800114800114800114

2d16h: ISDN BR2/0/1 Q931: RX <- CONNECT pd = 8 callref = 0x84

Progress Ind i = 0x8482 - Destination address is non-ISDN

Nov 12 08:24:52 EST: %ISDN-6-CONNECT: Interface BRI2/0/1:1 is now connected to 1

8043477539 N/A

2d16h: ISDN BR2/0/1 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x04

new_lexington_res#

Nov 12 08:24:58 EST: %ISDN-6-CONNECT: Interface BRI2/0/1:1 is now connected to 1

8043477539 N/A

Nov 12 08:25:07 EST: %ISDN-6-DISCONNECT: Interface BRI2/0/1:1 disconnected from

18045551212 , call lasted 14 seconds

2d16h: ISDN BR2/0/1 Q931: TX -> DISCONNECT pd = 8 callref = 0x04

Cause i = 0x8090 - Normal call clearing

2d16h: ISDN BR2/0/1 Q931: RX <- RELEASE pd = 8 callref = 0x84

2d16h: ISDN BR2/0/1 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x04

new_lexington_res#

2d16h: ISDN BR2/0/1 Q931: Applying typeplan for sw-type 0xC is 0x0 0x0, Calling

num 3025

2d16h: ISDN BR2/0/1 Q931: TX -> SETUP pd = 8 callref = 0x03

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x81

Preferred, B1

Keypad Facility i = '18045551211'

Calling Party Number i = 0x0080, '3025'

Plan:Unknown, Type:Unknown

2d16h: ISDN BR2/0/1 Q931: RX <- CALL_PROC pd = 8 callref = 0x83

Channel ID i = 0x89

Exclusive, B1

Locking Shift to Codeset 5

Codeset 5 IE 0x2A i = 0x80880B, '18045551211', 0x8001098001148001148001

14

2d16h: ISDN BR2/0/1 Q931: RX <- ALERTING pd = 8 callref = 0x83

Progress Ind i = 0x8288 - In-band info or appropriate now available

Signal i = 0x01 - Ring back tone on

2d16h: ISDN BR2/0/1 Q931: RX <- CONNECT pd = 8 callref = 0x83

Signal i = 0x3F - Tones off

Nov 12 08:23:38 EST: %ISDN-6-CONNECT: Interface BRI2/0/1:1 is now connected to 1

8045551211 N/A

2d16h: ISDN BR2/0/1 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x03

Nov 12 08:23:44 EST: %ISDN-6-CONNECT: Interface BRI2/0/1:1 is now connected to 1

8045551211 N/A

Nov 12 08:23:51 EST: %ISDN-6-DISCONNECT: Interface BRI2/0/1:1 disconnected from

18043597070 , call lasted 12 seconds

2d16h: ISDN BR2/0/1 Q931: TX -> DISCONNECT pd = 8 callref = 0x03

Cause i = 0x8090 - Normal call clearing

2d16h: ISDN BR2/0/1 Q931: RX <- RELEASE pd = 8 callref = 0x83

2d16h: ISDN BR2/0/1 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x03

As suspected the network doesn't generate alerting for calls to cell. Since it's unlikely you can have them to do so, please see:

http://cisco.com/en/US/tech/tk1077/technologies_tech_note09186a0080094c33.shtml#voipcalls

Hope this helps, please rate post if it does!

I was already given that document by a co-worker and tried those steps with no success.

Seth

Please send current DP config.

dial-peer voice 145 pots

corlist outgoing call-domestic

description dial peer for PSTN LongDistance

preference 1

destination-pattern 91[2-9]..[2-9]......

progress_ind setup enable 3

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

direct-inward-dial

port 2/0/1

forward-digits 11

Hi,

per document you should be sending PI 3 in setup, this is not happening. Which exact IOS is this

Do you have "voice rtp send-recv" in global config ?

Can you try "tone ringback alert-no-pi" please ?

The IOS is c3845-advipservicesk9-mz.124-11.XW1.bin

I did not have the "voice rtp send-recv" in global config but I added it with no luck.

Here is the dial-peer now.

dial-peer voice 145 pots

corlist outgoing call-domestic

tone ringback alert-no-PI

description dial peer for PSTN LongDistance

preference 1

destination-pattern 91[2-9]..[2-9]......

progress_ind setup enable 3

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

direct-inward-dial

port 2/0/1

forward-digits 11

Hi,

XW1 has been deferred, can you try latest XW4 or XJ4. I'm not positive that it would solve, but it's worth a try.

i have a 3845,running ios 12.4.12b

with fxo connecting to pbx

and no ringback tone too!