11-13-2007 09:25 PM
I have a question I'm not sure if it difficult or not. I have a NM-32a in
my 2611xm using IOS version: 2600-jk9s-mz.123-24.b. The problem is that I cannot setup the 2611xm to connect to my other cisco devices. I have read Cisco's Configuring a Terminal / Comm server (Doc ID:5466) and it has not helped me I still can't connect any of the devices. Any idea?
Access-Server(config)#do sh run
version 12.3
!
hostname Access-Server
!
boot-start-marker
boot-end-marker
!
enable secret xxx
!
memory-size iomem 10
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
!
!
ip host Router1 2033 172.21.1.1
ip host Router2 2034 172.21.1.1
ip host Router3 2035 172.21.1.1
ip host Router4 2035 172.21.1.1
ip host Router5 2036 172.21.1.1
!
username cisco password 0 cisco
!
!
interface Loopback1
ip address 172.21.1.1 255.255.255.0
!
interface FastEthernet0/0
ip address 139.x.x.50 255.255.255.0
duplex auto
speed auto
!
line con 0
line 33 64
transport input telnet
flowcontrol hardware
line aux 0
line vty 0 4
password cisco
login
Access-Server#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 2 0 0/0 -
* 33 TTY 9600/9600 - - - - - 0 48 52/158 -
* 34 TTY 9600/9600 - - - - - 1 25 53/164 -
* 35 TTY 9600/9600 - - - - - 0 88 8/26 -
* 36 TTY 9600/9600 - - - - - 0 13 17/54 -
* 37 TTY 9600/9600 - - - - - 1 0 0/0 -
38 TTY 9600/9600 - - - - - 2 0 0/0 -
39 TTY 9600/9600 - - - - - 0 11 12/37 -
40 TTY 9600/9600 - - - - - 0 11 19/59 -
41 TTY 9600/9600 - - - - - 0 17 27/82 -
42 TTY 9600/9600 - - - - - 0 37 36/110 -
43 TTY 9600/9600 - - - - - 0 0 0/0 -
44 TTY 9600/9600 - - - - - 0 23 0/0 -
45 TTY 9600/9600 - - - - - 0 0 0/0 -
46 TTY 9600/9600 - - - - - 0 0 0/0 -
47 TTY 9600/9600 - - - - - 0 27 0/0 -
48 TTY 9600/9600 - - - - - 0 0 0/0 -
49 TTY 9600/9600 - - - - - 0 11 0/0 -
50 TTY 9600/9600 - - - - - 0 1 0/3 -
51 TTY 9600/9600 - - - - - 0 0 0/0 -
52 TTY 9600/9600 - - - - - 0 0 0/0 -
53 TTY 9600/9600 - - - - - 0 0 0/0 -
54 TTY 9600/9600 - - - - - 0 0 0/0 -
11-13-2007 10:32 PM
Still you seem to have missed a few settings. the following must be in the config:
line 33 64
transport preferred telnet
transport input all
Please post a "sh line" for one of the lines on the NM32A.
regards,
Leo
11-17-2007 10:57 AM
thanks lgijssel,
it works.
However, I cant ssh to the router remotely. Please advise
11-18-2007 12:20 PM
Please check the link below:
Hope this helps you on your way.
regards,
Leo
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: