11-14-2007 12:04 PM - edited 03-03-2019 07:33 PM
We currently have a functioning T1, just purchased a second T1 for the 3meg capability (was told by our rep that our current equipment will work).
Question.
1. Is it possible to combine the 2 T1 in the 1750?
2. Can you help or give me some links to refrences that may help?
After some reading I gather that the router must support MLFR (yes we are runung a T1 over Frame Relay). Does this router support MLFR? The version is 12.3.
Any help with this topic will be be greatly appreciated. Thanks
11-14-2007 12:47 PM
1 & 2 - Yes.
This is your config guide:
http://cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_guide09186a0080087cbf.html
Hope this helps, please rate post if it does!
11-14-2007 07:42 PM
Thanks, I already looked at that, I guess I should have been more specific.
When I try to enter the command "interface mfr mfr1" I am getting invalid command, I even tried "interface mfr1" same thing, I can however configure the subinterface. Its wired that I cannot configure the main mfr, Any Ideas.
Again Router is 1751 and Ios is 12.3
11-14-2007 08:00 PM
Hi
Pls give the config you are doing with " sh ip int br"
Regards
JD
11-14-2007 08:19 PM
Station_Router#sh ip int br
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 #.#.#.# YES NVRAM up up
Serial0/0 #.#.#.# YES NVRAM up up
Serial1/0 unassigned YES unset up down
Station_Router#
Thanks
11-14-2007 08:59 PM
Config ? "sh run"
JD
11-14-2007 09:03 PM
Station_Router#sh run
Building configuration...
Current configuration : 1275 bytes
!
! Last configuration change at 02:42:26 edt Mon Nov 5 2007
! NVRAM config last updated at 23:18:58 edt Sun Nov 4 2007
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Station_Router
!
boot-start-marker
boot-end-marker
!
enable password qqqqqqqqqqqqq
!
clock timezone edt -5
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
ip cef
!
!
!
ip flow-cache timeout active 1
no ftp-server write-enable
!
!
!
!
interface FastEthernet0/0
ip address #.#.#.# 255.255.255.0
no ip route-cache cef
ip route-cache flow
no ip mroute-cache
speed 100
full-duplex
!
interface Serial0/0
ip address #.#.#.#255.255.255.252
encapsulation frame-relay IETF
no ip route-cache cef
ip route-cache flow
no ip mroute-cache
no fair-queue
!
interface Serial1/0
no ip address
!
ip classless
ip route 0.0.0.0 0.0.0.0 #.#.#.#
no ip http server
!
snmp-server community scrubber RO
snmp-server community conpres RW
snmp-server ifindex persist
snmp-server enable traps tty
!
line con 0
password 7 qqqqqqqqqqq
line aux 0
password 7 qqqqqqqqqqqqqqqqq
line vty 0 4
password 7 qqqqqqqqqqqqq
login
!
!
end
Station_Router#
11-14-2007 09:41 PM
Hi
can you try giving "encap fra mfr1"
on both the interfaces and then try "int mfr1"
Regards
JD
11-15-2007 04:58 AM
Same thing.
Station_Router(config-if)#encap fra mfr1
^
% Invalid input detected at '^' marker.
Thanks
11-15-2007 05:19 AM
It can happen that the 1750 platform was not getting the feature at the same announced time of 12.2(T).
So you should upgrade to something like latest 12.4 mainline and try again. You may also need to upgrade flash and ram at the same time.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide