cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
855
Views
9
Helpful
7
Replies

DHCP over 1300 Bridges

johnminon
Level 1
Level 1

I have 1300 bridges in station root and non-root mode and all the vlans can communicate across it with address assigned. But when a new unit (pc or phone) is attached.....the DHCP broadcast does not get sent across the wireless link to the DHCP server. What config change is needed to allow these broadcasts?

7 Replies 7

bbxie
Level 3
Level 3

if the DHCP server and client are on different vlan, make sure DHCP relay is enabled in the attached router/L3 switch

The DHCP server is on a router with a fastethernet set up as a dot1q trunk with all the vlans attached as sub-interfaces.

It is the broadcast that is not going across the wireless connection.

If i were to apply DHCP relay...where would i put it???

Thanks

The DHCP relay would need to be on the first layer 3 interface that the broadcast will get to.

Do you have a switch attaced to the non-root bridge or are you just directly attaching a device to the bridge?

If you are using a switch, you will need to set the switchport to use the proper VLAN that you desire.

As for the DHCP scope being on the router, you need to be certain that is in the same network as the VLAN you are connecting to. If your switchport is setup for VLAN10, and you do not have scope defined in the network space for VLAN10, then you will not get an address.

DHCP scopes will only assign an address to a device that is in the same VLAN that it is established for.

Can you post the router config?

Seth

Her is the pertinent info from router:

no ip dhcp use vrf connected

ip dhcp excluded-address 10.1.102.0 10.1.102.10

ip dhcp excluded-address 10.1.102.251 10.1.102.255

!

ip dhcp pool ipphone

network 10.1.102.0 255.255.255.128

default-router 10.1.102.1

option 150 ip 10.1.249.40 10.1.249.140

domain-name pdcarea.lcl

dns-server 10.1.1.10

interface Loopback0

ip address 10.1.255.2 255.255.255.255

!

interface FastEthernet0/0

description Trunk to sw1

no ip address

duplex auto

speed auto

!

interface FastEthernet0/0.200

description VLAN 200 Wireless Infrastructure

encapsulation dot1Q 200

ip address 10.1.200.1 255.255.255.240

no snmp trap link-status

!

interface FastEthernet0/0.300

description VLAN 300 Data xxxxx

encapsulation dot1Q 300

ip address 10.1.2.10 255.255.255.0

no snmp trap link-status

!

interface FastEthernet0/0.400

description VLAN 400 voice xxxx

encapsulation dot1Q 400

ip address 10.1.102.1 255.255.255.0

no snmp trap link-status

!

interface FastEthernet0/1

ip address 10.1.240.9 255.255.255.248

duplex full

speed 100

!

and on the switches I have all the ports set up as dot1q trunks with vlan 200 as the native to match the BVI interface.

I am passing multiple vlans across the wireless bridge such like a wired trunk port....

Thanks

John M.

What IOS version are using on the bridges? There were

some bugs in older versions with DHCP not working.

I have an almost identical setup (trunk-bridging,

Cisco router as DHCP server), this works with IOS 12.3(11)JA1.

There is no DHCP-relay necessary.

One thing strange in your router config:

The netmask for your DHCP-pool "ipphone" is 255.255.255.128,

while on the interface Fa0/0.400 it is 255.255.255.0.

Version 12.4(3g)JA1 is the IOS I am using...am going to check the bug tool kit

The addressing issue is correct.....that is a typo.....good lookin out!!!!

Thanks

Upgraded the IOS to 12.4(10b)JA and it works now. There is no bug on the old IOS....looked for a while.

Thanks for the help

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: