cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1254
Views
0
Helpful
7
Replies

%SYS-4-CHUNKMALLOCFAIL: Could not allocate chunks for ATM0/0/0

Nicholas Poole
Level 1
Level 1

I am having a problem with a 2811 that keeps getting this messsage:

Nov 16 18:34:58.645: %SYS-4-CHUNKMALLOCFAIL: Could not allocate chunks for ATM0/0/0

Total free: 0, Total inuse: 16, Cause : Not a dynamic chunk

-Process= "ATM Periodic", ipl= 4, pid= 80, -Traceback= 0x416A3DFC 0x400C3188 0x400C31EC 0x4037C4BC 0x400C5C1C

This causes the DSL interface to crash.

Sounds to me like a software caused memory issue, but I am at the top of my IOS release now and no improvement.

Has anyone seen this or got any sugestions?

7 Replies 7

cpartsenidis
Level 1
Level 1

I'm experiencing the same issue with a customer's 2811. Have you had any progress with the problem ?

paolo bevilacqua
Hall of Fame
Hall of Fame

Which exact IOS and DSL FW are you running?

The router is a 2811 running c2800nm-adventerprisek9-mz.124-15.T1.bin and has 256Mb Dram.

I've been advised to downgrade to 12.4.11T to see if it makes any difference.

Any suggestions ?

IOS should not make a difference.

What matters is that you upgrade the DSL FW, you can access at:

ftp://ftp.cisco.com/pub/access/800

The one you want is 3.0.x, there is a document describing how to install it.

Bevilacqua,

Here's the show dsl interface output. As you'll see, its already running firmware 3.0.014. Do you think I should still upgrade the firmware ?

ATM0/1/0

Alcatel 20190 chipset information

ATU-R (DS) ATU-C (US)

Modem Status: Showtime (DMTDSL_SHOWTIME)

DSL Mode: ITU G.992.1 (G.DMT) Annex B

ITU STD NUM: 0x03 0x2

Vendor ID: 'STMI' 'BDCM'

Vendor Specific: 0x0000 0x6110

Vendor Country: 0x0F 0xB5

Chip ID: C196 (0)

DFE BOM: DFE3.0 Annex B (2)

Capacity Used: 25% 31%

Noise Margin: 31.5 dB 27.0 dB

Output Power: 17.5 dBm 12.0 dBm

Attenuation: 18.0 dB 13.5 dB

Defect Status: None None

Last Fail Code: None

Watchdog Counter: 0xE3

Watchdog Resets: 0

Selftest Result: 0x00

Subfunction: 0x00 (UR2)

Interrupts: 8254 (0 spurious)

PHY Access Err: 0

Activations: 1

LED Status: OFF

LED On Time: 0

LED Off Time: 0

Init FW: init_AMR-3.0.014_no_bist.bin

Operation FW: AMR-3.0.014.bin

FW Source: embedded

FW Version: 3.0.14

Interleave Fast Interleave Fast

Speed (kbps): 0 2048 0 256

Cells: 0 297623 0 8495637

Reed-Solomon EC: 0 0 0 0

CRC Errors: 0 0 0 1

Header Errors: 0 0 0 0

Total BER: 0E-0 0E-0

Leakage Average BER: 0E-0 0E-0

ATU-R (DS) ATU-C (US)

Bitswap: enabled enabled

Bitswap success: 0 0

Bitswap failure: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin

000: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

010: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

020: 0 4 4 4 5 5 5 5 4 4 4 4 4 4 4 4

030: 4 4 3 3 3 3 2 2 0 0 0 0 4 4 5 5

040: 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5

050: 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6

060: 0 2 5 5 5 5 6 5 5 5 5 5 6 5 5 5

070: 5 5 5 5 5 5 5 5 5 5 5 5 5 4 5 5

080: 5 4 4 5 5 4 4 5 5 4 4 5 5 4 4 4

090: 5 4 4 4 4 4 3 4 4 4 0 3 4 4 0 0

0A0: 4 4 0 0 0 4 0 0 0 4 0 0 0 4 0 0

0B0: 0 0 0 0 0 3 0 0 4 4 0 3 0 3 4 4

0C0: 0 3 4 3 0 3 4 0 0 3 4 0 0 0 0 0

0D0: 0 0 0 0 0 0 3 4 3 3 4 4 3 3 3 3

0E0: 4 3 4 3 3 0 0 0 3 3 3 3 3 3 3 0

0F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

ATM0/3/0

Alcatel 20190 chipset information

Line has not yet been activated.

Modem Status: Down (DMTDSL_DO_OPEN)

DSL Mode: Unknown

Interrupts: 659859 (0 spurious)

PHY Access Err: 0

Activations: 0

LED Status: OFF

LED On Time: 0

LED Off Time: 0

Init FW: init_AMR-3.0.014_no_bist.bin

Operation FW: AMR-3.0.014.bin

FW Source: embedded

DSL: Training log buffer capability is not enabled

Hi,

yes to be on the safe side I would try first to upgrade to 3.0.33.

Failing that you may need help from the tac for further troubleshooting.

In the mean time I swapped my HWIC DSL for an old WIC which has resolved the issue. So i have looked at the firmware on this to compare it but its not the same chipset. Do you know where if this has new firmware and if so what the url is?

ATM0/0/0

Alcatel 20150 chipset information

ATU-R (DS) ATU-C (US)

Modem Status: Showtime (DMTDSL_SHOWTIME)

DSL Mode: ITU G.992.1 (G.DMT) Annex A

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: