Nokia Intellisync 1.1

Unanswered Question
Nov 28th, 2007

Anyone is able to run Nokia Intellisync 1.1 on Nokia Eseries and register the phone on CallManager?

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4 (1 ratings)
Loading.
Stefano Amici Wed, 11/28/2007 - 03:52

I solved the issue: the SCCP phone on Cisco CallManager for 1.1 must be a 7970 and not 7960 as for 1.0.

nyciscotech Wed, 11/28/2007 - 06:13

According to the Nokia user guide/release notes, it mentions Callmanager should be configured as a S60 (plugin necessary for Callmanager) and for Callmanager express versions it should be configured as a 7970.

Stefano Amici Thu, 11/29/2007 - 08:42

Could you give me the link where i can download the 1.1 release notes and CallManager plugin?

On Nokia site i can find only Intellisync 1.0 user guide and release notes.

Thanks,

Stefano

a.gooding Thu, 11/29/2007 - 08:45

anyone ever got the E series working with just the SIP client?

anderson-david Fri, 11/30/2007 - 07:01

Hi Arvind,

I had this confirmed by Cisco that this doesn't work, the only way to get the Nokia phones working was with the Client

I hope this helps

Dave

Stefano Amici Fri, 11/30/2007 - 08:01

Nokia E65 and E61i works in SIP on CCM and CCME while E61 doesn't work.

Stefano

a.gooding Thu, 12/13/2007 - 18:44

guys,

someone previous posted a config to get this working.Thread - http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddedac9/8#selected_message

i never did get it working using SIP.

Anderson i know you said the SIP would not work but im hearing mixed opinions.

anyone have a clear answer and/or config to get this working with teh SIP client?

thanks in advance

jeroenhermans Thu, 12/13/2007 - 23:24

Hi,

I can confirm The build in SIP client is working on the Nokia E60, E61 and E90 using CUCM 6. Possibly on other eseries devices as well but I have only tested these 3.

These are the settings needed on the Nokia device :

Profile name: CUCM6

Service Profile: IETF

Default Access point: *your wifi access point*

Public user name: sip:[email protected] <= (your [email protected] server address)

Use compression: No

Registration: On demand or Always on

Use security: No

Proxy server

Proxy server address: sip:172.16.10.105 < = (host name CUCM SIP Realm CFG)

Realm: CUC6009941 < = (host name CUCM SIP Realm CFG)

User name: 1000 <= ( your extension, configured in SIP Realm user name)

Password: *your password* <= ( configured in SIP Realm pwd)

Allow loose routing: Yes

Transport Type: UDP

Port:5065

Registrar Server

Registrat serv. addr.: sip:172.16.10.105 < = (host name CUCM SIP Realm CFG)

Realm: CUC6009941 < = (host name CUCM SIP Realm CFG)

User name: 1000 <= ( your extension, configured in SIP Realm user name)

Password: *your password*

Transport Type: UDP

Port:5060

CUCM6 CFG

SIP Realm

Realm: CUC6009941

user: 1000

pwd: password

End User Configuration:

UserID=1000

Digest Credentials=password

insert device based on MAC

3rd party basic sip phone

assosiate device

System - Security Profile - Phone Security Profile

Third-party SIP Device (Advanced) - Standard SIP Non-Secure Profile

Third-party SIP Device (Standard) - Standard SIP Non-Secure Profile

enable Enable Digest Authentication and set transport type

security template enable Digest Credentials

Create a new SIP Profile "NOKIA E61 Standard SIP Profile" allowing you to change specific settings

System - Enterprise Parameters: change parameter " ccmsipline" to "CUC6009941" & auto registration from SCCP to SIP

Kind Regards,

Jeroen

a.gooding Fri, 12/14/2007 - 04:22

thanks for the great info. However, you said version 6, we have version 5.1.2(b) currently and was under the impression that it would have worked with this as well.

Note*** Not seeing ccmsipline parameter under ent param.

thanks again

Thucnk_FPT_FIS_6 Mon, 01/07/2008 - 20:24

Hi Jeroen

I am configuring SIP Phone in NOKIA E90 with CCM 6.0. When I add a new Sip Profile, I encounter an error : "Profiles in same realm must have same user name" in NOKIA E90. I checked user name. Everything is OK. I can't save this profile.

Can you tell me the solution for this issue?

Thanks.

jeroenhermans Wed, 01/09/2008 - 02:21

Hi,

When working with the build in sip client on the Nokia, it is always best to have only 1 profile defined.

So, try and delete all the existing ones you have and only add the one you will use for CCM 6

Rgds,

Jeroen

ivan.garrido Thu, 01/17/2008 - 07:50

Hi,

I attach the config, the ephone 11(7940) and ephone 22(Nokia) sharing line 105.

Thanks,

Ivan

!

interface FastEthernet0/0.20

description Gateway Voz

encapsulation dot1Q 20

--More-- ip address 10.56.1.1 255.255.255.0

h323-gateway voip bind srcaddr 10.56.1.1

!

tftp-server flash:P00403020214.bin

tftp-server flash:CP7912060000SCCP050124A.sbin

tftp-server flash:apps11.1-0-0-72.sbn

tftp-server flash:cnu11.3-0-0-81.sbn

tftp-server flash:cvm11.7-2-0-66.sbn

tftp-server flash:dsp11.1-0-0-73.sbn

tftp-server flash:jar11.7-2-0-66.sbn

tftp-server flash:SCCP11.7-2-1-0S.loads

tftp-server flash:term11.default.loads

!

control-plane

!

!

!

voice-port 0/0/0

station-id name FAX CHILE

!

voice-port 0/0/1

!

voice-port 0/0/2

!

voice-port 0/0/3

!

!

dial-peer voice 540 voip

tone ringback alert-no-PI

destination-pattern *5T

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

modem passthrough nse codec g711ulaw

session target ipv4:10.1.100.239

dtmf-relay cisco-rtp h245-signal h245-alphanumeric

ip qos dscp cs5 media

no vad

!

dial-peer voice 541 voip

--More-- tone ringback alert-no-PI

preference 2

destination-pattern *5T

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

modem passthrough nse codec g711ulaw

session target ipv4:10.1.100.238

dtmf-relay cisco-rtp h245-signal h245-alphanumeric

ip qos dscp cs5 media

no vad

!

!

!

telephony-service

max-ephones 30

max-dn 30

ip source-address 10.56.1.1 port 2000

auto assign 1 to 30

system message LOGICALIS - CHILE

url services http://10.56.0.8/services.asp

user-locale ES

time-zone 18

time-format 24

create cnf-files version-stamp 7960 Jan 11 2008 09:48:07

max-conferences 4 gain -6

web admin system name softnet password softnet

dn-webedit

time-webedit

transfer-system full-consult

transfer-pattern 1..

transfer-pattern *54...

transfer-pattern *.....

transfer-pattern *......

xmlschema grabacion

--More-- !

!

ephone-template 1

!

!

ephone-dn 11 dual-line

number 105

name CISTERNAS, Pedro

!

ephone-dn 22 dual-line

number 105

label Nokia E61

description telefono en prueba

name Nokia E61

!

ephone 11

mac-address 000E.8492.D528

type 7940

button 1:11

!

ephone 22

description prueba NOKIA

mac-address 0019.790F.AC84

type 7960

button 1:22

!

line con 0

line aux 0

line vty 0 4

access-class 2 in

privilege level 15

transport input ssh

line vty 5 15

access-class 2 in

privilege level 15

transport input ssh

!

scheduler allocate 20000 1000

ntp master 1

end

RT-Softnet#

RT-Softnet#sh tele

RT-Softnet#sh telephony-service

CONFIG (Version=3.3)

=====================

Version 3.3

Cisco CallManager Express

For on-line documentation please see:

www.cisco.com/univercd/cc/td/doc/product/access/ip_ph/ip_ks/index.htm

ip source-address 10.56.1.1 port 2000

max-ephones 30

max-dn 30

max-conferences 4 gain -6

dspfarm units 0

dspfarm transcode sessions 0

hunt-group report delay 1 hours

max-redirect 5

user-locale ES

time-format 24

date-format mm-dd-yy

timezone 18 SA Eastern Standard Time

url services http://10.56.0.8/services.asp

transfer-pattern 1..

transfer-pattern *54...

transfer-pattern *.....

transfer-pattern *......

keepalive 30

timeout interdigit 10

timeout busy 10

timeout ringing 180

caller-id name-only: enable

system message LOGICALIS - CHILE

web admin system name softnet password softnet

web admin customer name Customer

edit DN through Web: enabled.

edit TIME through web: enabled.

Log (table parameters):

max-size: 150

retain-timer: 15

create cnf-files version-stamp 7960 Jan 11 2008 09:48:07

transfer-system full-consult

auto assign 1 to 30

local directory service: enabled.

xml schema grabacion

Paolo Bevilacqua Thu, 01/17/2008 - 09:22

Hi,

you cut the configuration due to "more". So I don't see two ephones both with button 1:22 as expected.

ivan.garrido Thu, 01/17/2008 - 09:43

Thank you!!

I configured both ephone with button 1:11 and now the sharing line is working fine!!

My mistake was to configure both ephone with diferents button (1:11 and 1:22), but the same number in both button.

Thanks a lot.

Ivan.

Actions

This Discussion