cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1260
Views
4
Helpful
16
Replies

Nokia Intellisync 1.1

Stefano Amici
Level 1
Level 1

Anyone is able to run Nokia Intellisync 1.1 on Nokia Eseries and register the phone on CallManager?

16 Replies 16

Stefano Amici
Level 1
Level 1

I solved the issue: the SCCP phone on Cisco CallManager for 1.1 must be a 7970 and not 7960 as for 1.0.

According to the Nokia user guide/release notes, it mentions Callmanager should be configured as a S60 (plugin necessary for Callmanager) and for Callmanager express versions it should be configured as a 7970.

Could you give me the link where i can download the 1.1 release notes and CallManager plugin?

On Nokia site i can find only Intellisync 1.0 user guide and release notes.

Thanks,

Stefano

anyone ever got the E series working with just the SIP client?

Hi Arvind,

I had this confirmed by Cisco that this doesn't work, the only way to get the Nokia phones working was with the Client

I hope this helps

Dave

Nokia E65 and E61i works in SIP on CCM and CCME while E61 doesn't work.

Stefano

guys,

someone previous posted a config to get this working.Thread - http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddedac9/8#selected_message

i never did get it working using SIP.

Anderson i know you said the SIP would not work but im hearing mixed opinions.

anyone have a clear answer and/or config to get this working with teh SIP client?

thanks in advance

Hi,

I can confirm The build in SIP client is working on the Nokia E60, E61 and E90 using CUCM 6. Possibly on other eseries devices as well but I have only tested these 3.

These are the settings needed on the Nokia device :

Profile name: CUCM6

Service Profile: IETF

Default Access point: *your wifi access point*

Public user name: sip:1000@172.16.10.105 <= (your extension@your server address)

Use compression: No

Registration: On demand or Always on

Use security: No

Proxy server

Proxy server address: sip:172.16.10.105 < = (host name CUCM SIP Realm CFG)

Realm: CUC6009941 < = (host name CUCM SIP Realm CFG)

User name: 1000 <= ( your extension, configured in SIP Realm user name)

Password: *your password* <= ( configured in SIP Realm pwd)

Allow loose routing: Yes

Transport Type: UDP

Port:5065

Registrar Server

Registrat serv. addr.: sip:172.16.10.105 < = (host name CUCM SIP Realm CFG)

Realm: CUC6009941 < = (host name CUCM SIP Realm CFG)

User name: 1000 <= ( your extension, configured in SIP Realm user name)

Password: *your password*

Transport Type: UDP

Port:5060

CUCM6 CFG

SIP Realm

Realm: CUC6009941

user: 1000

pwd: password

End User Configuration:

UserID=1000

Digest Credentials=password

insert device based on MAC

3rd party basic sip phone

assosiate device

System - Security Profile - Phone Security Profile

Third-party SIP Device (Advanced) - Standard SIP Non-Secure Profile

Third-party SIP Device (Standard) - Standard SIP Non-Secure Profile

enable Enable Digest Authentication and set transport type

security template enable Digest Credentials

Create a new SIP Profile "NOKIA E61 Standard SIP Profile" allowing you to change specific settings

System - Enterprise Parameters: change parameter " ccmsipline" to "CUC6009941" & auto registration from SCCP to SIP

Kind Regards,

Jeroen

thanks for the great info. However, you said version 6, we have version 5.1.2(b) currently and was under the impression that it would have worked with this as well.

Note*** Not seeing ccmsipline parameter under ent param.

thanks again

Hi Jeroen

I am configuring SIP Phone in NOKIA E90 with CCM 6.0. When I add a new Sip Profile, I encounter an error : "Profiles in same realm must have same user name" in NOKIA E90. I checked user name. Everything is OK. I can't save this profile.

Can you tell me the solution for this issue?

Thanks.

Hi,

When working with the build in sip client on the Nokia, it is always best to have only 1 profile defined.

So, try and delete all the existing ones you have and only add the one you will use for CCM 6

Rgds,

Jeroen

Hi,

I configured the Nokia CallConnect 1.37 SCCP client with CME 3.3. This worked fine, but when I configured the same DN in other IP Phone ( Shared Line) , I call the DN, but only ringing the Nokia or the IP Phone, but not both...

Someone have tested this?

Thanks,

Ivan Garrido

ivan.garrido@la.logicalis.com

Ivan, send config please ?

Hi,

I attach the config, the ephone 11(7940) and ephone 22(Nokia) sharing line 105.

Thanks,

Ivan

!

interface FastEthernet0/0.20

description Gateway Voz

encapsulation dot1Q 20

--More-- ip address 10.56.1.1 255.255.255.0

h323-gateway voip bind srcaddr 10.56.1.1

!

tftp-server flash:P00403020214.bin

tftp-server flash:CP7912060000SCCP050124A.sbin

tftp-server flash:apps11.1-0-0-72.sbn

tftp-server flash:cnu11.3-0-0-81.sbn

tftp-server flash:cvm11.7-2-0-66.sbn

tftp-server flash:dsp11.1-0-0-73.sbn

tftp-server flash:jar11.7-2-0-66.sbn

tftp-server flash:SCCP11.7-2-1-0S.loads

tftp-server flash:term11.default.loads

!

control-plane

!

!

!

voice-port 0/0/0

station-id name FAX CHILE

!

voice-port 0/0/1

!

voice-port 0/0/2

!

voice-port 0/0/3

!

!

dial-peer voice 540 voip

tone ringback alert-no-PI

destination-pattern *5T

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

modem passthrough nse codec g711ulaw

session target ipv4:10.1.100.239

dtmf-relay cisco-rtp h245-signal h245-alphanumeric

ip qos dscp cs5 media

no vad

!

dial-peer voice 541 voip

--More-- tone ringback alert-no-PI

preference 2

destination-pattern *5T

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

modem passthrough nse codec g711ulaw

session target ipv4:10.1.100.238

dtmf-relay cisco-rtp h245-signal h245-alphanumeric

ip qos dscp cs5 media

no vad

!

!

!

telephony-service

max-ephones 30

max-dn 30

ip source-address 10.56.1.1 port 2000

auto assign 1 to 30

system message LOGICALIS - CHILE

url services http://10.56.0.8/services.asp

user-locale ES

time-zone 18

time-format 24

create cnf-files version-stamp 7960 Jan 11 2008 09:48:07

max-conferences 4 gain -6

web admin system name softnet password softnet

dn-webedit

time-webedit

transfer-system full-consult

transfer-pattern 1..

transfer-pattern *54...

transfer-pattern *.....

transfer-pattern *......

xmlschema grabacion

--More-- !

!

ephone-template 1

!

!

ephone-dn 11 dual-line

number 105

name CISTERNAS, Pedro

!

ephone-dn 22 dual-line

number 105

label Nokia E61

description telefono en prueba

name Nokia E61

!

ephone 11

mac-address 000E.8492.D528

type 7940

button 1:11

!

ephone 22

description prueba NOKIA

mac-address 0019.790F.AC84

type 7960

button 1:22

!

line con 0

line aux 0

line vty 0 4

access-class 2 in

privilege level 15

transport input ssh

line vty 5 15

access-class 2 in

privilege level 15

transport input ssh

!

scheduler allocate 20000 1000

ntp master 1

end

RT-Softnet#

RT-Softnet#sh tele

RT-Softnet#sh telephony-service

CONFIG (Version=3.3)

=====================

Version 3.3

Cisco CallManager Express

For on-line documentation please see:

www.cisco.com/univercd/cc/td/doc/product/access/ip_ph/ip_ks/index.htm

ip source-address 10.56.1.1 port 2000

max-ephones 30

max-dn 30

max-conferences 4 gain -6

dspfarm units 0

dspfarm transcode sessions 0

hunt-group report delay 1 hours

max-redirect 5

user-locale ES

time-format 24

date-format mm-dd-yy

timezone 18 SA Eastern Standard Time

url services http://10.56.0.8/services.asp

transfer-pattern 1..

transfer-pattern *54...

transfer-pattern *.....

transfer-pattern *......

keepalive 30

timeout interdigit 10

timeout busy 10

timeout ringing 180

caller-id name-only: enable

system message LOGICALIS - CHILE

web admin system name softnet password softnet

web admin customer name Customer

edit DN through Web: enabled.

edit TIME through web: enabled.

Log (table parameters):

max-size: 150

retain-timer: 15

create cnf-files version-stamp 7960 Jan 11 2008 09:48:07

transfer-system full-consult

auto assign 1 to 30

local directory service: enabled.

xml schema grabacion

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: