11-30-2007 08:09 PM - edited 03-05-2019 07:45 PM
Dear all,
I have a setup like
Cisco12416 Router-- Catalyst4000--Customer Router
config at switch and router are as follow
Switch4000#
interface GigabitEthernet7/7
switchport access vlan 77
switchport mode access
speed 100
duplex full
spanning-tree bpdufilter enable
end
Switch4000#
interface GigabitEthernet7/8
switchport access vlan 78
switchport mode access
speed 100
duplex full
spanning-tree bpdufilter enable
end
Router12416#
interface GigabitEthernet6/0/2.77
bandwidth 4096
encapsulation dot1Q 77
ip address x.x.x.x
ip load-sharing per-packet
rate-limit input 4096000 768000 1536000 conform-action transmit exceed-action drop
rate-limit output 4096000 768000 1536000 conform-action transmit exceed-action drop
end
Router12416#
interface GigabitEthernet6/0/2.78
bandwidth 4096
encapsulation dot1Q 78
ip address 125.x.x.157 255.255.255.252
no ip directed-broadcast
rate-limit input 4096000 768000 1536000 conform-action transmit exceed-action drop
rate-limit output 4096000 768000 1536000 conform-action transmit exceed-action drop
end
Pl. let me know what config should I do at switch4000 and router12416 and customer router
Thanks & Regards
Mahesh
11-30-2007 11:23 PM
Hi Mahesh,
Please let me know your requirement.It is not clear.Also please let me know where Gi7/7 and 7/8 are connected.
Regards
Nambi
11-30-2007 11:27 PM
see,
gi7/7 and 7/8 is connected to customer router fe ports
Now from this 4000 switch a trunk link goes to my 12416 router
I want ether channel between 4000 (gi7/7 and 7/8)and customer router
that's it
if had confusion let me know
i am confused b'se i can't configure any Ip address on 4000 switch ..I have to do routing on 12416 router only
Mahesh
11-30-2007 11:51 PM
Hi Mahesh,
You can have an access/trunk etherchannel on the switch side.
If you have only one subnet you can use,
- access port channel on switch side and ip
on the physical int of the customer router.
If you have more than one subnet you can use,
- trunk port channel on switch side and ip
on the port channel int of the customer
router.
Please try this.
Case 1:
Switch :
--------
int range gi7/7-8
no shut
channe-group 10 mode on
switchport
switchport mode access
switchport mode access vlan x
int po10
switchport mode access
switchport mode access vlan x
end
Case 2:
Switch :
--------
int range gi7/7-8
no shut
channe-group 10 mode on
switchport
switchport mode trunk
int po10
switchport mode trunk
end
You need to use mode "on" on the router side also.
HTH,
Nambi
12-01-2007 12:22 AM
Ok,
My activity is tomorrow
let me check and revert to you
Mahesh
12-01-2007 12:29 AM
Dear nambi,
I had one confusion as at router12416 end should I create one subinterface or two ?
As I am going to use only one subnet so is it possible that I create only one interface at Router12416 and give Ip on that Router ?
Pl. clarify that how will i extend those vlan to Router
Regards
mahesh
12-02-2007 05:53 AM
Dear it didn't work,
My end config
--------------
interface Port-channel5
ip address 125.16.156.153 255.255.255.252
duplex full
end
interface GigabitEthernet7/7
no ip address
speed 100
duplex full
spanning-tree bpdufilter enable
channel-group 5 mode on
end
interface GigabitEthernet7/8
no ip address
speed 100
duplex full
spanning-tree bpdufilter enable
channel-group 5 mode on
end
and customer end config
------------------
interface Port-channel5
ip address 125.16.156.154 255.255.255.252
duplex full
interface FastEthernet0/1/0
no ip address
duplex full
speed 100
channel-group 5
interface FastEthernet0/2/0
no ip address
duplex full
speed 100
channel-group 5
----------------
both end po5 show up but unable to ping to each other
Regards
Mahesh
12-02-2007 08:23 PM
Dear experts,
Pl. reply on this issue
Mahesh
12-03-2007 06:24 AM
Hi Mahesh,
Give us the output of show int po 5 and show etherchannel summary from switch and the router... That will be helpful.
Thx
12-03-2007 07:00 PM
Switch:
Port-channel5 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 0016.c73d.2b3f (bia 0016.c73d.2b3f)
MTU 1552 bytes, BW 200000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is N/A
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi7/7 Gi7/8
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
71 packets input, 28257 bytes, 0 no buffer
Received 71 broadcasts (71 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
988 packets output, 63390 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
------------------------
Router:
Port-channel5 is up, line protocol is up
Hardware is FEChannel, address is 001a.6c70.108c (bia 001d.a189.1de0)
Internet address is 125.16.156.154/30
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
No. of active members in this channel: 1
Member 0 : FastEthernet0/1/0 , Full-duplex, 100Mb/s
No. of Non-active members in this channel: 0
Last input 01:55:44, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/809/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
52 packets output, 3324 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
No other output avalable
Regards
Mahesh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide