AIM-ATM-4T1 - installation and configuration (IMA config)

Unanswered Question
Dec 7th, 2007

Hello all,

I'm trying to configure 4 Data T1's from AT&T. I've purchased the AIM-ATM-4T1 Bundle, in AIM 0 on the board and installed the T1 controllers in WIC 0 and 1. in config mode i cannot seem to apply the "mode atm" in the controller sub-config? i've upgraded to the appropriate image?

wanr2-60mad-4n(config)#controller T1 0/0/0

wanr2-60mad-4n(config-controller)#mode ?

cas Configure CAS (Channel Associated Signal) mode

ccs Configure CCS (Common Channel Signal) mode

------------------------------------------

wanr2-60mad-4n#sh ver

Load for five secs: 0%/0%; one minute: 0%; five minutes: 0%

Time source is NTP, 12:46:34.842 EST Fri Dec 7 2007

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(11)T, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Sat 18-Nov-06 17:16 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

wanr2-60mad-4n uptime is 1 hour, 4 minutes

System returned to ROM by reload at 11:40:46 EST Fri Dec 7 2007

System restarted at 11:42:11 EST Fri Dec 7 2007

System image file is "flash:c2800nm-adventerprisek9-mz.124-11.T.bin"

Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.

Processor board ID FHK1140F3U8

2 Gigabit Ethernet interfaces

4 Channelized T1/PRI ports

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

-----------------------------------------

wanr2-60mad-4n#sh diag

Slot 0:

C2821 Motherboard with 2GE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

Onboard VPN : v2.3.3

EEPROM contents at hardware discovery:

PCB Serial Number : FOC113748D8

Hardware Revision : 1.0

Top Assy. Part Number : 800-26921-03

Board Revision : A0

Deviation Number : 0

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20070918

Chassis Serial Number : FHK1140F3U8

Chassis MAC Address : 001d.a106.6d88

MAC Address block size : 32

CLEI Code : COM7M00ARA

Product (FRU) Number : CISCO2821

Part Number : 73-8853-05

Version Identifier : V04

WIC Slot 0:

T1 (2 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision F0

Serial number 32419598 Part number 800-04477-03

FRU Part Number VWIC-2MFT-T1=

Test history 0x0 RMA number 00-00-00

WIC Slot 1:

T1 (2 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision F0

Serial number 32419772 Part number 800-04477-03

FRU Part Number VWIC-2MFT-T1=

Test history 0x0 RMA number 00-00-00

-----------------------------------------

while there seems to be a lot of information on this type of scenario, none specifies the 2800 series..mostly 2600 and 3600's? Anybody?

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
chris_tan Sun, 12/09/2007 - 23:07

Hi,

You are purchased a bundle, which should come with 2 VWIC2 and 1 AIM-ATM (CISCO High Performance ATM Advanced Integration Module), i believe your vendor did not install AIM-ATM or the AIM-ATM module is faulty. Please check with your vendor.

Hope it help. :-)

Rgds.

Christopher

Actions

This Discussion