ospf on 3550 vs 4500

Unanswered Question
Dec 8th, 2007
User Badges:

Im having the following command on a switch 3550, but when I try now migrating it over to 4500, I cannot get the same command in, can you help me?


router ospf 109

log-adjacency-changes

network 10.56.1.0 0.0.0.255 area 0.0.0.0

!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Jon Marshall Sat, 12/08/2007 - 05:37
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

Hi Jorge


Which bit of the config won't go in, all of it ?


What error message are you getting ?


Which IOS version are you running on the 4500 ?


Jon

jorge.s Sat, 12/08/2007 - 06:41
User Badges:

Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12

.2(25)EWA10, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 11-Jul-07 00:08 by dchih

Image text-base: 0x10000000, data-base: 0x114BC038


ROM: 12.2(31r)SG3

Pod Revision 14, Force Revision 34, Tie Revision 32


ITC0004 uptime is 3 hours, 30 minutes

Uptime for this control processor is 3 hours, 30 minutes

System returned to ROM by Stateful Switchover

System restarted at 12:09:46 cet Sat Dec 8 2007

System image file is "bootflash:cat4000-i9s-mz.122-25.EWA10.bin"


cisco WS-C4510R (MPC8540) processor (revision 11) with 524288K bytes of memory.

Processor board ID FOX11140THS

MPC8540 CPU at 800Mhz, Supervisor V-10GE

Last reset from PowerUp

15 Virtual Ethernet interfaces

296 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.


Configuration register is 0x2102


Edison Ortiz Sat, 12/08/2007 - 10:02
User Badges:
  • Super Bronze, 10000 points or more
  • Hall of Fame,

    Founding Member

You have a basic L3 image. For OSPF support, you need the enhanced L3 image cat4000-i5s-mz.122-25.EWA10.bin

jorge.s Sat, 12/08/2007 - 11:54
User Badges:

You are right, I didn't upgraded it has I tought.

now should be ok, but how do I configure OSP?


ITC0004#sh ver

Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I5S-M), Version 12

.2(25)EWA12, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Thu 15-Nov-07 18:21 by kellythw

Image text-base: 0x10000000, data-base: 0x114BC884


ROM: 12.2(31r)SG3

Pod Revision 14, Force Revision 34, Tie Revision 32


ITC0004 uptime is 8 hours, 43 minutes

Uptime for this control processor is 7 hours, 54 minutes

System returned to ROM by redundancy reset

System restarted at 12:58:09 cet Sat Dec 8 2007

System image file is "bootflash:cat4000-i5s-mz.122-25.EWA12.bin"


cisco WS-C4510R (MPC8540) processor (revision 11) with 524288K bytes of memory.

Processor board ID FOX11140THS

MPC8540 CPU at 800Mhz, Supervisor V-10GE

Last reset from Redundancy Reset

15 Virtual Ethernet interfaces

296 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.


Configuration register is 0x2102


ITC0004#


Jon Marshall Sat, 12/08/2007 - 11:58
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

Jorge


Not sure what you mean about how do you configure OSPF. ?


As per your example in your original post


router ospf 10

network 10.56.1.0 0.0.0.255 area 0

network 10.57.1.0 0.0.0.255 area 0


etc.


Jon

Actions

This Discussion