2501 stuck in cold start

Unanswered Question

Hi, all.

I have a 2501 router. Everytime, when it starts, it stops, saying snmp agent on host router is undergoing a cold start...

even when it wouldnt stop when i type break to go Rommon mode.

what might be the problem. I've copied the message here.


===========



00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state


to up


00:00:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta


te to down


00:00:20: %SYS-5-CONFIG_I: Configured from memory by console


00:00:23: %LINK-5-CHANGED: Interface Serial0, changed state to administratively


down


00:00:23: %LINK-5-CHANGED: Interface Serial1, changed state to administratively


down


00:00:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state


to down


00:00:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state


to down


00:01:04: %SYS-5-RESTART: System restarted --


Cisco Internetwork Operating System Software


IOS (tm) 2500 Software (C2500-IO-L), Version 12.2(26), RELEASE SOFTWARE (fc2)


Copyright (c) 1986-2004 by cisco Systems, Inc.


Compiled Sat 31-Jul-04 03:32 by eaarmas


00:01:04: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold star


tˇ


System Bootstrap, Version 11.0(10c), SOFTWARE


Copyright (c) 1986-1996 by cisco Systems


2500 processor with 16384 Kbytes of main memory




F3: 9286440+846656+770252 at 0x3000060




Restricted Rights Legend




Use, duplication, or disclosure by the Government is


subject to restrictions as set forth in subparagraph


(c) of the Commercial Computer Software - Restricted


Rights clause at FAR sec. 52.227-19 and subparagraph


(c) (1) (ii) of the Rights in Technical Data and Computer


Software clause at DFARS sec. 252.227-7013.




cisco Systems, Inc.


170 West Tasman Drive


San Jose, California 95134-1706








Cisco Internetwork Operating System Software


IOS (tm) 2500 Software (C2500-IO-L), Version 12.2(26), RELEASE SOFTWARE (fc2)


Copyright (c) 1986-2004 by cisco Systems, Inc.


Compiled Sat 31-Jul-04 03:32 by eaarmas


Image text-base: 0x03050A44, data-base: 0x00001000




cisco 2500 (68030) processor (revision A) with 16384K/2048K bytes of memory.


Processor board ID 01207578, with hardware revision 00000000


Bridging software.


X.25 software, Version 3.0.0.


1 Ethernet/IEEE 802.3 interface(s)


2 Serial network interface(s)


32K bytes of non-volatile configuration memory.


16384K bytes of processor board System flash (Read ONLY)








Press RETURN to get started!






00:00:07: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up


00:00:08: %LINK-3-UPDOWN: Interface Serial0, changed state to up


00:00:08: %LINK-3-UPDOWN: Interface Serial1, changed state to down


00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state


to up


00:00:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta


te to down


00:00:20: %SYS-5-CONFIG_I: Configured from memory by console


00:00:21: %LINK-5-CHANGED: Interface Serial0, changed state to administratively


down


00:00:23: %LINK-5-CHANGED: Interface Serial1, changed state to administratively


down


00:00:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state


to down


00:00:26: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state


to down


00:01:04: %SYS-5-RESTART: System restarted --


Cisco Internetwork Operating System Software


IOS (tm) 2500 Software (C2500-IO-L), Version 12.2(26), RELEASE SOFTWARE (fc2)


Copyright (c) 1986-2004 by cisco Systems, Inc.


Compiled Sat 31-Jul-04 03:32 by eaarmas


00:01:04: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold star


tˇ

+++++++++++STOPS HERE, then i reboot it.


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
glen.grant Mon, 12/10/2007 - 16:18
User Badges:
  • Purple, 4500 points or more

Are you saying that it starts rebooting over and over by itself ? Otherwise that is a normal end of boot message meaning it is ready to configure , just hit the enter key at that point.

Actions

This Discussion