12-10-2007 07:12 PM - edited 03-13-2019 04:47 PM
Has anyone ever connected a Muzak system for moh to a ccme router?
Solved! Go to Solution.
12-11-2007 07:28 AM
Hi Christopher,
I have not done this, but it certainly is supported on CME. The details are noted below;
Configuring Music on Hold from a Live Feed
To configure music on hold from a live feed, perform the following steps.
Prerequisites
â¢SIP phones require Cisco Unified CME 4.1 or a later version.
â¢VIC2-2FXO, VIC2-4FXO, EM-HDA-3FXS/4FXO, EM-HDA-6FXO, or EM2-HDA-4FXO
â¢For a live feed from VoIP, VAD must be disabled.
Restrictions
â¢A foreign exchange station (FXS) port cannot be used for a live feed.
SUMMARY STEPS
1. enable
2. configure terminal
3. voice-port port
4. input gain decibels
5. auto-cut-through (E&M only)
6. operation 4-wire (E&M only)
7. signal immediate (E&M only)
8. signal loop-start live-feed (FXO only)
9. no shutdown
10. exit
11. dial peer voice tag pots
12. destination-pattern string
13. port port
14. exit
15. ephone-dn dn-tag
16. number number
17. moh [out-call outcall-number] [ip ip-address port port-number [route ip-address-list]]
18. exit
19. ephone phone-tag
20. multicast-moh
21. end
From this good CME doc (with detailed steps);
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010511
Hope this helps!
Rob
12-11-2007 07:28 AM
Hi Christopher,
I have not done this, but it certainly is supported on CME. The details are noted below;
Configuring Music on Hold from a Live Feed
To configure music on hold from a live feed, perform the following steps.
Prerequisites
â¢SIP phones require Cisco Unified CME 4.1 or a later version.
â¢VIC2-2FXO, VIC2-4FXO, EM-HDA-3FXS/4FXO, EM-HDA-6FXO, or EM2-HDA-4FXO
â¢For a live feed from VoIP, VAD must be disabled.
Restrictions
â¢A foreign exchange station (FXS) port cannot be used for a live feed.
SUMMARY STEPS
1. enable
2. configure terminal
3. voice-port port
4. input gain decibels
5. auto-cut-through (E&M only)
6. operation 4-wire (E&M only)
7. signal immediate (E&M only)
8. signal loop-start live-feed (FXO only)
9. no shutdown
10. exit
11. dial peer voice tag pots
12. destination-pattern string
13. port port
14. exit
15. ephone-dn dn-tag
16. number number
17. moh [out-call outcall-number] [ip ip-address port port-number [route ip-address-list]]
18. exit
19. ephone phone-tag
20. multicast-moh
21. end
From this good CME doc (with detailed steps);
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010511
Hope this helps!
Rob
12-11-2007 08:52 AM
Thanks Rob, I have seen that document before, just curious if anyone has ever done this before. I got it working by following the steps above, worked first time, not bad at all.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: