Solved: multiple CME no translation profile occured

Seifeddine-Tlili · ‎12-17-2007

Hi every one plz can anyone help to figure this things out, i'll sum up my prob

I have 2 CME conencted via interface serial

an i have defined a dial-pattern between them but when i dial from router1 3100 the call must be forwared to the number 100 and the translation profile has to applied but it doesn't work cauz when i type debug voip dialpeer the destination number don't change and still 3100 and no phone ring :) only disconnected tone

jolo07310 · ‎12-18-2007

Hi,

According your debug, you are calling from ext 122 to 2133.

Correct me if I am wrong.

It seems doesnt make sense for me, according the debug, I saw the configuration at CME, you have dn 122 and 2133, see blow.

Basically, you are calling at the same CME, not crossing to another CME.

ephone-dn 2

number 122

application recorder

!

ephone-dn 3

number 2133

name karfatchou

Base on the dial-peer below, you should call extension start with 3 follow 3 digits, like 3001 to another CME.

dial-peer voice 2 voip

destination-pattern 3...

session target ipv4:192.168.2.1

codec g711ulaw

no vad

!

dial-peer voice 3 voip

translation-profile incoming profile1

incoming called-number .

Also, please add following command under voip dial-peer.

dtmf-relay h245-alphanumeric

no vad

Another thing is that, I saw you put codec g711ulaw under dial-peer voice 2 voip which it will send out G711. The default is G729.

you should put G711 under incoming voip dial-peer another side also....

dial-peer voice 3 voip

translation-profile incoming profile1

incoming called-number .

codec g711ulaw

Ken

View solution in original post

jolo07310 · ‎12-17-2007

Hi SEIFEDDINE,

Here is the link might help you to interconnect TWO CME together, you might read the doc alredy:

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/multcme.html

Here is my question:

1. Does it work without translation profile??

Can you send me debug when you make a call:

debug voip dialpeer all

Also send me the outcome:

sh dial-peer voice summary

Thanks

Ken

Seifeddine-Tlili · ‎12-17-2007

yes without a translation it work perfecly but i have to change my dian plan for that i mean i assign for example a number 3100 for an ephone and then from the remote phone i dial the 3100 and i get my call :)

jolo07310 · ‎12-17-2007

The configuration seems fine for me.

Can you change at the both end?

dial-peer voice 2 voip

translation-profile incoming profile1

incoming called-number .

dtmf-relay h245-alphanumeric

no vad

"incoming called-number ." means accept all the digits.

If still doesnt work, please send the debug and show command from the last post.

Ken

Seifeddine-Tlili · ‎12-17-2007

i have to do this tomorrow cauz i'm out of the office i'll be back tomorrow ;) thanks for ur help i really appreciate it

Seifeddine-Tlili · ‎12-18-2007

hy Sir hope every things is well for ya, so i have configured in the router as u told to do before but unfortunatly without results but what it makes me confused was the result shown by the debug cmd i was like the configurations was OK the incoming dialpeer was matched and so far i can view the excact tag that it matchs

here is the result of the debug cmd and the show dial-peer voice summary and sh run cmds

thanks for your help :)

jolo07310 · ‎12-18-2007

Hi,

According your debug, you are calling from ext 122 to 2133.

Correct me if I am wrong.

It seems doesnt make sense for me, according the debug, I saw the configuration at CME, you have dn 122 and 2133, see blow.

Basically, you are calling at the same CME, not crossing to another CME.

ephone-dn 2

number 122

application recorder

!

ephone-dn 3

number 2133

name karfatchou

Base on the dial-peer below, you should call extension start with 3 follow 3 digits, like 3001 to another CME.

dial-peer voice 2 voip

destination-pattern 3...

session target ipv4:192.168.2.1

codec g711ulaw

no vad

!

dial-peer voice 3 voip

translation-profile incoming profile1

incoming called-number .

Also, please add following command under voip dial-peer.

dtmf-relay h245-alphanumeric

no vad

Another thing is that, I saw you put codec g711ulaw under dial-peer voice 2 voip which it will send out G711. The default is G729.

you should put G711 under incoming voip dial-peer another side also....

dial-peer voice 3 voip

translation-profile incoming profile1

incoming called-number .

codec g711ulaw

Ken

Seifeddine-Tlili · ‎12-18-2007

heyn thanks i finally fix it an it was a codec problem :)

jolo07310 · ‎12-18-2007

Great to hear that... :) always like to hear the feedback at the NetPro

Ken