Solved: How to configure Etherchannel on Router 3845 L2 Interface?

manik.palekar · ‎12-18-2007

Greetings!!!

I have router with l2 card ,i have planned to configure etherchannel to do a loadbancing .But etherchanel commands are supporting on l2 interface.

paolo bevilacqua · ‎12-19-2007

Hi, as neikumar stated before, the HWIC-4ESW doesn't support etherchannel.

Hope this helps, please rate post if it does!

View solution in original post

paolo bevilacqua · ‎12-18-2007

Which "l2" card do you have ?

manik.palekar · ‎12-18-2007

Hi ,

Thanks for support ,I have NM card.Please find the below details.....Thanks

Slot 1:

Mueslix-4T Port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision M0

Serial number 34559939 Part number 800-02314-02

FRU Part Number NM-4T=

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x00: 01 54 01 01 02 0F 57 C3 50 09 0A 02 00 00 00 00

0x10: B0 0A 7C 00 06 01 22 00 00 05 FF FF FF FF FF FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF

Nagendra Kumar Nainar · ‎12-18-2007

Hi Manik,

Please be advised that HWIC-ESW card doesnt support port aggregation (ether channel). You may need Etherswitch Network module for port aggregation.

Regards,

Nagendra

manik.palekar · ‎12-18-2007

Hello Naikumar ,

Thanks for support ,I have NM card.Please find the below details.....Thanks

Slot 1:

Mueslix-4T Port adapter, 4 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware revision 1.1 Board revision M0

Serial number 34559939 Part number 800-02314-02

FRU Part Number NM-4T=

Test history 0x0 RMA number 00-00-00

EEPROM format version 1

EEPROM contents (hex):

0x00: 01 54 01 01 02 0F 57 C3 50 09 0A 02 00 00 00 00

0x10: B0 0A 7C 00 06 01 22 00 00 05 FF FF FF FF FF FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF

ekhoo · ‎12-18-2007

Hi Manik,

base on the router output above. You are using 4 port Synchronous Serial Network Module on slot1.

You CANNOT configure "etherchanel" on this Serial network module.

As per Naikumar advised. you need an Etherswitch Network module for port aggregation.

regards,

Sean Khoo

manik.palekar · ‎12-19-2007

Hello Frd ,

please find the module details ...

WIC Slot 0:

4 Port FE Switch

Base MAC Address : 0016.c8de.8348

MAC Address block size : 4

PCB Serial Number : FOC10040RCV

Hardware Revision : 5.1

Part Number : 73-8474-05

Board Revision : B0

Top Assy. Part Number : 800-24193-01

Deviation Number : 0

Fab Version : 05

CLEI Code : IPUIAE0RAA

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : HWIC-4ESW

Version Identifier : VN/A

Connector Type : 01

EEPROM format version 4

EEPROM contents (hex):

paolo bevilacqua · ‎12-19-2007

Hi, as neikumar stated before, the HWIC-4ESW doesn't support etherchannel.

Hope this helps, please rate post if it does!

bvsnarayana03 · ‎12-19-2007

have u tried the methods mentioned by me?