cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1011
Views
0
Helpful
7
Replies

3700 router with NME16es-1G-p module

tcherry
Level 1
Level 1

I am having a heck of a time configuring this module and being able to access it and see the port status. I have been on Cisco's website and just having a hard time getting to the right documentation. The router is version 12.4(18) ip base. I have not been able to seeion into the module. When I do a sh inventory it is displayed in the inventory.

NAME: "3745 chassis", DESCR: "3745 chassis"

PID: , VID: 2.0, SN: JMX

NAME: "c3745 Motherboard with Fast Ethernet", DESCR: "c3745 Motherboard with Fas

t Ethernet"

PID: C3745-2FE , VID: 2.0, SN: JAE

NAME: "WAN Interface Card - Serial 2T", DESCR: "WAN Interface Card - Serial 2T"

PID: WIC-2T= , VID: 1.0, SN: 286

NAME: "Wan Interface Card BRI U (2091)", DESCR: "Wan Interface Card BRI U (2091)

"

PID: WIC-1B-U= , VID: 4.0, SN: 27

NAME: "NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE", DESCR: "NME-16ES-1G

-P: EtherSwitch SM 16 10/100T PoE + 1 GE"

PID: NME-16ES-1G-P , VID: V01 , SN: FOC

7 Replies 7

Jon Marshall
Hall of Fame
Hall of Fame

Hi

Have a look at this document which should help you setup the initial config to gain access to the module.

Basically after the module is installed you see a new unused gigabit interface. In short you need to

1) Give the new interface an IP address and issue a "no shut"

2) After this issue the command "service-module gi"slot/int" session

This will then connect you to the module and you can configure it from there.

http://www.cisco.com/en/US/products/hw/modules/ps2797/products_configuration_example09186a0080810449.shtml

HTH

Jon

I keep getting the message:

% Connection timed out; remote host not responding

I did a no shut and assigned an IP address with no problem.

What do you get from the output of

service-module gi1/0 status (where gi1/0 is the gigabit connection to the module).

From my 2800 router

Router#service-module gi1/0 status

Service Module is Cisco GigabitEthernet1/0

Service Module supports session via TTY line 66

Service Module is in Steady state

Service Module reset on error is disabled

Getting status from the Service Module, please wait..

EtherSwitch Service Module with 16 FE ports and 1 GE port

System name = 2800-esw

Model string = NME-16ES-1G

System board ID = 0x4018

Base MAC addr = 0017.5978.6200

Switch number = 1

System uptime = 29 days, 13 hours, 32 minutes, 37 seconds

Software Details:

Operating System = Cisco C3750 IOS Software

Vesrion = 12.2(25)SEC2

Major version = 1

Minor Vesrion = 12

Image path = flash:c3750-ipbase-mz.122-25.SEC2/c3750-ipbase-mz.122-25.SEC2.bin

Router#

Atlanta#service-module gigabitEthernet 1/0 status

Service Module is Cisco GigabitEthernet1/0

Service Module supports session via TTY line 33

Service Module is in Steady state

Service Module reset on error is disabled

Getting status from the Service Module, please wait..

EtherSwitch Service Module with 16 PoE FE ports and 1 GE port

System name = Switch

Model string = NME-16ES-1G-P

System board ID = 0x18

Base MAC addr = 0018.182b.5700

Switch number = 1

System uptime = 0 days, 0 hours, 1 minute, 34 seconds

Software Details:

Operating System = Cisco C3750 IOS Software

Vesrion = 12.2(25)SEC

Major version = 1

Minor Vesrion = 12

Image path = flash:c3750-ipbasek9-mz.122-25.SEC/c3750-ipbasek9-mz.122-25

.SEC.bin

Looks fine to me from the status. You could try a reset on the module

service-module g1/0 reset

When you try and connect with "service-module gi1/0 sess" what do you see ?

I get

Router#service-module gi1/0 session

Trying 10.5.5.1, 2066 ... Open

2800-esw>

I do have to hit return to get the 2800-esw> prompt.

Jon

I tried moving it to another open slot but I still get a connection timed out message. status still looks good.

Atlanta#service-module gigabitEthernet 3/0 status

Service Module is Cisco GigabitEthernet3/0

Service Module supports session via TTY line 97

Service Module is in Steady state

Service Module reset on error is disabled

Getting status from the Service Module, please wait..

EtherSwitch Service Module with 16 PoE FE ports and 1 GE port

System name = Switch

Model string = NME-16ES-1G-P

System board ID = 0x18

Base MAC addr = 0018.182b.5700

Switch number = 1

System uptime = 0 days, 0 hours, 3 minutes, 35 seconds

Software Details:

Operating System = Cisco C3750 IOS Software

Vesrion = 12.2(25)SEC

Major version = 1

Minor Vesrion = 12

Image path = flash:c3750-ipbasek9-mz.122-25.SEC/c3750-ipbasek9-mz.122-25

.SEC.bin

Can't see too much wrong with this.

if you do a "sh line" from router prompt presumably vty97 is free. You could try clearing the line just to be on the safe side.

I'm running c2800nm-ipbase-mz.124-3c.bin on my 2800.

Jon

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: