missing config/ can not add it too

Unanswered Question
Jan 13th, 2008
User Badges:

Team,

I have a 6509, and a WS-F6K-MSFC2,

when i do show run, i see no config for module 15, which is where the msfc is:


here is the current output:

compared whith what i had in the backup output of show run, few days ago:


#module 9 empty

!

#module 15 : 1-port Multilayer Switch Feature Card

!

#module 16 empty



BEFORE:




#module 9 empty

!

#module 15 : 1-port Multilayer Switch Feature Card

set module name 15

set module enable 15

set vlan 1 15/1

set port name 15/1

set cdp enable 15/1

set trunk 15/1 nonegotiate isl 1-1005,1025-4094

set spantree portcost 15/1 4

set spantree portpri 15/1 32

set spantree portvlanpri 15/1 0

set spantree portvlancost 15/1 cost 3

set spantree guard none 15/1

set port gmrp 15/1 enable

set gmrp registration normal 15/1

set gmrp fwdall disable 15/1

!

#module 16 empty




the customer did replace the chassis, and the sup, but not the MSFC,


and I can not add that config in,

i get the following when i try to add it fromthe backup above:


MSP-OP5DTESTSWA> (enable) set mod ena 15

Feature not supported on Module 15.



anyone seen this before ?

the reason the customer replaced that HW, because the switch was reloading.


here is an outpout of show mod too for your view:



(enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

3 3 8 1000BaseX Ethernet WS-X6408A-GBIC no ok

4 4 8 1000BaseX Ethernet WS-X6408A-GBIC no ok

5 5 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok


Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAD05010NJK

15 SAD05020798

3 SAD04470M6U

4 SAD05010BUM

5 SAL04440VVF


Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-04-c0-f8-41-e6 to 00-04-c0-f8-41-e7 7.0 5.3(1) 6.4(17)

00-04-c0-f8-41-e4 to 00-04-c0-f8-41-e5

00-0c-86-a2-3e-80 to 00-0c-86-a2-42-7f

15 00-04-c1-cc-bf-80 to 00-04-c1-cc-bf-bf 1.1 12.1(8b)E1 12.1(8b)E19

3 00-02-fc-22-1d-d8 to 00-02-fc-22-1d-df 1.3 5.4(2) 6.4(17)

4 00-03-32-b9-93-9e to 00-03-32-b9-93-a5 1.3 5.4(2) 6.4(17)

5 00-03-6c-29-65-f0 to 00-03-6c-29-66-1f 1.4 5.4(2) 6.4(17)


Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- ----------------------- ------------------- ----------- ------

1 L3 Switching Engine WS-F6K-PFC SAD0501037J 1.1


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
glen.grant Sun, 01/13/2008 - 17:23
User Badges:
  • Purple, 4500 points or more

You have to "session " into module 15 , which basically telnetting into module 15 . Here you put in your userid and password. This is where all your layer 3 config info is . You are running a hybrid box which is catos on the layer 2 side and IOS on the layer 3 side . You are looking at the layer2 side . Hopefully you saved your layer 3 config before replacing the module. If he replaced the supervisor he replaced the msfc also or he would have had to unplug the msfc module from the current supervisor because it is a daughter card on the supervisor.

Actions

This Discussion