cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
387
Views
3
Helpful
2
Replies

3620 router and "WIC-1DSU-T1-V2" T1 card support.

dtochilovsky
Level 1
Level 1

Hello All. Anyone know if the 3620 router supports the WIC-1DSU-T1-V2 T1 WIC?

I insert the card into the NM-1FE2W Port adapter but the card is not being recognized. I get: " WIC Slot 1: Unknown WAN daughter card"

The router is running IOS version 12.2(5d) and I know that the IOS must be 12.2.17 for the card to be supported.

Do I need to just update the IOS to a newer version?

This is the output of the "show diag" on the router :

Slot 1:

NM-1FE2W Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

Top Assy. Part Number : 800-04796-01

Board Revision : G0

Deviation Number : 0-0

Fab Version : 05

PCB Serial Number : JAD061105M9

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 D7 41 01 00 C0 46 03 20 00 12 BC 01

0x10: 42 47 30 80 00 00 00 00 02 05 C1 8B 4A 41 44 30

0x20: 36 31 31 30 35 4D 39 03 00 81 00 00 00 00 04 00

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

FT1

Hardware revision 1.4 Board revision F1

Serial number 17175863 Part number 800-03279-04

Test history 0x0 RMA number 00-00-00

Connector type Wan Module

EEPROM format version 2

EEPROM contents (hex):

0x20: 02 11 01 04 01 06 15 37 50 0C CF 04 00 00 00 00

0x30: 79 00 00 00 99 11 24 01 FF FF FF FF FF FF FF FF

WIC Slot 1:

Unknown WAN daughter card

Hardware revision 64.0 Board revision >5

Serial number 1379991810 Part number 800-7441222-79

Test history 0x43 RMA number 49-49-52

Connector type PCI

EEPROM format version 4

EEPROM contents (hex):

0x20: 04 FF 40 00 52 41 01 02 C1 8B 46 4F 43 31 31 34

0x30: 35 32 52 55 51 82 49 20 9A 05 42 41 30 03 00 81

This is the "show ver" output:

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3620-I-M), Version 12.2(5d), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Sat 02-Feb-02 01:51 by kellythw

Image text-base: 0x600089A8, data-base: 0x60A54000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

MAN-RTR-3620 uptime is 6 days, 18 hours, 59 minutes

System returned to ROM by power-on

System image file is "flash:c3620-i-mz.122-5d.bin"

cisco 3620 (R4700) processor (revision 0x81) with 49152K/16384K bytes of memory.

Processor board ID 30404845

R4700 CPU at 80Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

3 Serial network interface(s)

DRAM configuration is 32 bits wide with parity disabled.

29K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Any help would be appreciated.

Thank you.

Dmitry.

2 Replies 2

Edison Ortiz
Hall of Fame
Hall of Fame

>Do I need to just update the IOS to a newer version?

Yup.

__

Edison.

Thank you!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco