01-27-2008 11:38 PM - edited 03-03-2019 08:26 PM
Product#: VWIC2-2MFT-T1/E1
Can use this with ATM connection.
i cannot use the command "mode atm aim 0"
thanks
Wael
Solved! Go to Solution.
01-29-2008 01:54 AM
Hi,
If you can see below output from "sh ver". Which mean you have correct AIM-ATM module installed. Else pls make sure you purchase it and install properly.
Processor board ID FHK1116F3CN
2 Gigabit Ethernet interfaces
1 ATM interface
2 Channelized E1/PRI ports
1 Virtual Private Network (VPN) Module
1 ATM/Voice AIM
Also, if you can see it. Please add "mode atm aim 0" under controller e1 0/0/0
controller E1 0/0/0
mode atm aim 0
Hope it help.
Thanks.
Rgds,
Christopher
01-29-2008 02:02 AM
Hi, to add to the good advice from Chris, I will try be even more clear:
You need to buy a piece of hardware called AIM-ATM, open the router, and fit it inside.
Without it, you cannot do ATM and the commands are not recognized.
As a recognition to those giving answers, please rate useful posts with the scrollbox below!
01-28-2008 02:50 AM
Do you have the AIM-ATM installed? Do "show diag" to check.
Hope this helps, please rate post if it does!
01-28-2008 10:23 PM
how to install that i am using Cisco Router 1841
01-29-2008 01:40 AM
Open the router and fit the module inside.
Hope this helps, please rate post if it does!
01-29-2008 01:44 AM
i already did that but i cannot make it work on ATM.
i cannot issue the commands.
my question is does this module supports ATM connection.?
01-29-2008 01:54 AM
Hi,
If you can see below output from "sh ver". Which mean you have correct AIM-ATM module installed. Else pls make sure you purchase it and install properly.
Processor board ID FHK1116F3CN
2 Gigabit Ethernet interfaces
1 ATM interface
2 Channelized E1/PRI ports
1 Virtual Private Network (VPN) Module
1 ATM/Voice AIM
Also, if you can see it. Please add "mode atm aim 0" under controller e1 0/0/0
controller E1 0/0/0
mode atm aim 0
Hope it help.
Thanks.
Rgds,
Christopher
01-29-2008 02:02 AM
Hi, to add to the good advice from Chris, I will try be even more clear:
You need to buy a piece of hardware called AIM-ATM, open the router, and fit it inside.
Without it, you cannot do ATM and the commands are not recognized.
As a recognition to those giving answers, please rate useful posts with the scrollbox below!
01-29-2008 02:10 AM
Thanks Bevilacqua and chris. That was my question The card that mentioned in the topic cannot act as ATM module.
i will buy ATM Module and try it.
i tried to do this it worked but i cannot add the command "mode atm aim 0" only "mode atm" without "aim 0"
card type e1 0/0/0:0
controller E1 0/0/0
mode atm
anyways thanks it seems this card is not compatible i will get ATM-AIM Module.
Thanks
Wael
01-29-2008 02:26 AM
Yes the card that you have can work in ATM mode but if you don't install the AIM-ATM, you cannot enter the ATM commands.
I've noticed that you haven't rated posts, would you consider doing so as an appreciation to those that are giving you free and good answers ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide