cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
931
Views
0
Helpful
11
Replies

ASA5505 No Internet Connectivity

greentw1972
Level 1
Level 1

I am setting up a new ASA 5505. The old firewallhas a IP x1.x2.x3.x4, subnet 255.255.255.192, gateway g1.g2.g3.g4, DNS d1.d2.d3.d4. I am connected to a cable modem

I cannot connect to the internet. Can someone please help, I am new to Cisco.

Result of the command: "show config": Saved

: Written by enable_15 at 17:50:24.909 CST Fri Feb 1 2008

!

ASA Version 7.2(3)

!

hostname xxxxx

domain-name default.domain.invalid

enable password R8oXOL9vUpDFQFqu encrypted

names

!

interface Vlan1

nameif inside

security-level 100

ip address 192.168.1.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

ip address x1.x2.x3.x4 255.255.255.192

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passwd 2KFQnbNIdI.2KYOU encrypted

ftp mode passive

clock timezone CST -6

clock summer-time CDT recurring

dns domain-lookup outside

dns server-group DefaultDNS

name-server d1.d2.d3.d4

domain-name default.domain.invalid

pager lines 24

logging enable

logging asdm informational

mtu inside 1500

mtu outside 1500

icmp unreachable rate-limit 1 burst-size 1

asdm image disk0:/asdm-523.bin

no asdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 1 0.0.0.0 0.0.0.0

route outside 0.0.0.0 0.0.0.0 g1.g2.g3.g4 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout uauth 0:05:00 absolute

http server enable

http 192.168.1.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd dns 69.1.30.11

!

dhcpd address 192.168.1.2-192.168.1.129 inside

dhcpd dns 192.168.1.1 interface inside

dhcpd enable inside

!

!

class-map inspection_default

match default-inspection-traffic

!

!

policy-map type inspect dns preset_dns_map

parameters

message-length maximum 512

policy-map global_policy

class inspection_default

inspect dns preset_dns_map

inspect ftp

inspect h323 h225

inspect h323 ras

inspect rsh

inspect rtsp

inspect esmtp

inspect sqlnet

inspect skinny

inspect sunrpc

inspect xdmcp

inspect sip

inspect netbios

inspect tftp

!

service-policy global_policy global

prompt hostname context

Cryptochecksum:c654e7d7b9580738e2bc70d4c3f3b9d4

1 Accepted Solution

Accepted Solutions
11 Replies 11

oszkari
Level 1
Level 1

Hi,

the configuration seems ok, you should have access to the internet.(if the ip, gw addresses are correct)

Do not check the internet access with ping, by default icmp packets are not permitted trough ASA.

dongdongliu
Level 1
Level 1

could you post any log ?

I have double checked everything. Attempting to connect with IE and no luck. Tried 2 different computers. Is there anything else I need to setup? This is a new install. Could it have something to do with the cable modem? As I mentioned the current firewall, Syamantec is working with these parameters.

I will try again in the morning and post a log.

Thanks for you help.

no dhcpd dns 192.168.1.1 interface inside

set a real dns server

dhcpd dns your_provider_dns_server_address interface inside

try using 4.2.2.4 as your DNS server and see if that works

I have not entered the DNS provided by my IPS. However this entry is in my configuration.

dhcpd dns 69.1.30.11

!

dhcpd address 192.168.1.2-192.168.1.129 inside

dhcpd dns 192.168.1.1 interface inside

dhcpd enable inside

Should I change the 192.168.1.1 to the 69.1.30.11?

yes

Should one of your ports have "switchport access vlan 1"?

Can you ping the firewalls inside interface?

Actually ignore that, it is probably default.

Setting the DNS worked. Thank you for your help.

Is there any other setting I need to make for security?

Thanks

It depends on the needs...

Now you have a fully functional SPI firewall,

which drops all the traffic which was not initiated from the inside lan.

You could filter the outgoing traffic too and

do some application layer inspection on http...lot of exploits circulate these days..

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: