02-06-2008 08:08 AM - edited 03-15-2019 08:39 AM
Hi,
We have a trouble with CallerID. We receive it from the telco, but CallManagerExpress does not process it. Here's the debug log of a test call I made.
ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x010D
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9F8B0100A11002010102010080084D4F4E415354204A
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x2183, '450581xxxx'
Plan:ISDN, Type:National
Called Party Number i = 0x80, '2505'
Plan:Unknown, Type:Unknown
013118: Feb 1 20:48:41.921: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x810D
Channel ID i = 0xA98381
Exclusive, Channel 1
ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x810D
ISDN Se0/0/0:23 Q931: TX -> CONNECT pd = 8 callref = 0x810D
ISDN Se0/0/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x010D
ISDN Se0/0/0:23 **ERROR**: call_progress: DEV_CONNECTED VOICE ERROR: Bearer capability not available(0x3A): b channel 0 call id 0xBA
%ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to 450581xxxx N/A
ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x010D
Cause i = 0x8090 - Normal call clearing
%ISDN-6-DISCONNECT: Interface Serial0/0/0:0 disconnected from 450581xxxx , call lasted 5 seconds
ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x810D
Feb 1 20:48:47.145: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x010D
See...
Facility i = 0x9F8B0100A11002010102010080084D4F4E415354204A
translates into
MONAST J
How can I tell CME to process those messages, and send them to the phones ?
Thank you!
Solved! Go to Solution.
02-06-2008 10:58 AM
Ok, I've found your previous message when the IE was not present at all. can you try:
voice service voip
qsig decode
02-06-2008 09:42 AM
Hi, which switchtype have you confgured, and which exact IOS version ?
You should be able to see the name when all is allright.
02-06-2008 09:45 AM
Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)
isdn switch-type primary-5ess
As the telco's requirement.
02-06-2008 10:10 AM
Whoops, I had forgot. Please configure
isdn supp-service name calling
under inteface.
Hope this helps, please rate post if it does!
02-06-2008 10:29 AM
It's already configured that way.
02-06-2008 10:58 AM
Ok, I've found your previous message when the IE was not present at all. can you try:
voice service voip
qsig decode
02-06-2008 11:04 AM
THANK YOU!
It worked !!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: