ASA CSC-SSM re-imaging process looping?

Unanswered Question
Feb 9th, 2008
User Badges:

Trying to re-image a CSC-SSM module but the recover boot procedure seems to be looping.


I configure then start the "hw mod 1 recover boot"...


thmasa1f# hw m 1 recover boot


The module in slot 1 will be recovered. This may

erase all configuration and all data on that device and

attempt to download a new image for it.

Recover module in slot 1? [confirm]

Recover issued for module in slot 1

thmasa1f#



As shown below the "debug module-boot" output displays it reading the image via tftp OK.

After completing the tftp download the message "Launching TFTP Image..." is displayed.


But then it seems to go back to downloading the tftp image again.

It keeps looping like this until I issuse the "hw mod 1 recover stop" command.


I have never done this procedure before, what should happen after downloading and executing the image?



Slot-1 957> Cisco Systems ROMMON Version (1.0(11)2) #0: Thu Jan 26 10:43:08 PST 2006

Slot-1 958> Platform ASA-SSM-CSC-10

Slot-1 959> GigabitEthernet0/0

Slot-1 960> Link is UP

Slot-1 961> MAC Address: 0018.1900.3518

Slot-1 962> ROMMON Variable Settings:

Slot-1 963> ADDRESS=192.168.0.111

Slot-1 964> SERVER=192.168.0.112

Slot-1 965> GATEWAY=0.0.0.0

Slot-1 966> PORT=GigabitEthernet0/0

Slot-1 967> VLAN=untagged

Slot-1 968> IMAGE=csc6.2.1599.0.bin

Slot-1 969> CONFIG=

Slot-1 970> LINKTIMEOUT=20

Slot-1 971> PKTTIMEOUT=4

Slot-1 972> RETRY=20

Slot-1 973> tftp [email protected]

Slot-1 974> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

.

.

.

Slot-1 158> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Slot-1 159> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Slot-1 160> Received 60835523 bytes

Slot-1 161> Launching TFTP Image...

Slot-1 162> Cisco Systems ROMMON Version (1.0(11)2) #0: Thu Jan 26 10:43:08 PST 2006

Slot-1 163> Platform ASA-SSM-CSC-10

Slot-1 164> GigabitEthernet0/0

Slot-1 165> Link is UP

Slot-1 166> MAC Address: 0018.1900.3518

Slot-1 167> ROMMON Variable Settings:

Slot-1 168> ADDRESS=192.168.0.111

Slot-1 169> SERVER=192.168.0.112

Slot-1 170> GATEWAY=0.0.0.0

Slot-1 171> PORT=GigabitEthernet0/0

Slot-1 172> VLAN=untagged

Slot-1 173> IMAGE=csc6.2.1599.0.bin

Slot-1 174> CONFIG=

Slot-1 175> LINKTIMEOUT=20

Slot-1 176> PKTTIMEOUT=4

Slot-1 177> RETRY=20

Slot-1 178> tftp [email protected]

Slot-1 179> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Slot-1 180> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

.

.

.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
m-haddad Thu, 07/09/2009 - 12:36
User Badges:
  • Silver, 250 points or more

I have the same problem with version 6.3. What was your fix?


Thanks,


GRAEME DANIELSON Mon, 07/13/2009 - 14:22
User Badges:

The solution in the end was hardware replacement. Once it was replaced the process worked.

Sorry I guess I should've posted a solution.

m-haddad Tue, 07/14/2009 - 12:44
User Badges:
  • Silver, 250 points or more

Thanks for the feedback. I have also opened a ticket with Cisco and they confirmed that the module is damaged. They sent me a new one to replace the damaged module.


Regards,


Actions

This Discussion