02-12-2008 09:34 PM
Hi netpros,
I need to upgrade a Cisco 3620 to a supported Cisco equivalent device. The customer uses this device for dedicated dial up remote access solution (ONRAMP10). Appart from access server, this device does nothing else. I am thinking a Cisco 2800 series or even a 1800 series ( I am not sure about this one). Your expert advice is much appreciated. Please see the relevant shows of the current device.
SydRas#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-I-M), Version 12.1(5)T5, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Mon 26-Feb-01 21:15 by ccai
Image text-base: 0x60008950, data-base: 0x60A26000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ROM: 3600 Software (C3620-I-M), Version 12.1(5)T5, RELEASE SOFTWARE (fc1)
SydRas uptime is 1 day, 1 hour, 6 minutes
System returned to ROM by reload at 12:34:24 Sydney Mon Feb 11 2008
System restarted at 12:35:09 Sydney Mon Feb 11 2008
System image file is "flash:c3620-i-mz.121-5.T5"
cisco 3620 (R4700) processor (revision 0x81) with 26624K/6144K bytes of memory.
Processor board ID 25121822
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
MICA-6DM Firmware: CP ver 2720 - 5/30/2000, SP ver 2720 - 5/30/2000.
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
11 Serial network interface(s)
30 terminal line(s)
2 Channelized E1/PRI port(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
SydRas#sh controllers e1
E1 1/0 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (414 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
E1 1/1 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (416 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 416 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 416 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 86400 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400 Unavail Secs
controller E1 1/0
pri-group timeslots 1-10,16
interface Serial1/0:15
no ip address
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice voice
!
interface Group-Async0
ip unnumbered Loopback1
encapsulation ppp
async mode dedicated
peer default ip address pool dialin_pool
ppp authentication ms-chap
group-range 1 30
02-13-2008 01:20 AM
Hi, yes a 1841 would do, there is now out a new 8 port async card in for of wic, would that work for you ?
02-13-2008 03:17 AM
Thanks Paolo,
Do you know the part number for that card .. so that I can do more research. Also would I be able to configure the ISDN part (ONRAMP10) similar to the current configuration as well ..?
appreciate your feedback !!!
02-13-2008 03:44 AM
The new cards are introduced here:
http://cisco.com/en/US/prod/collateral/modules/ps5949/ps6182/product_data_sheet0900aecd80274416.html
and the new PRI cards:
http://cisco.com/en/US/prod/collateral/modules/ps2797/product_data_sheet0900aecd80710c88.html
But I think in fact you need a minimum of a 2811 to terminate PRI.
02-13-2008 05:23 AM
Thanks Paolo,
that was very helpful .. so would you agree that I should be OK with a 2811 plus a Channelized T1/E1 and ISDN PRI Module and a 12 ports integrated digital modem.
your response is much appreciated !!!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: