02-16-2008 11:11 PM - edited 03-03-2019 08:44 PM
I have the following scenario:
We have a Cisco 2811 router in my HO which is used for corporate data network.
All the branch offices connect to this router through an MPLS data network.
Now, I would like to give some of the users access the Citrix Web interface.
I will add one WIC ADSL in the 2811 router for this purpose only, which
will be connecting to internet. It has public IP also.
Now, How do i configure the 2811 router to address this scenario? How do I give access the internet users and corporate users to the server (citrix) without changing the default gateway of the webserver?
Please provide me a step by step configuration to setup the WIC and routing as i dont have enough experience in Cisco
Thanks for any input.
02-17-2008 03:35 AM
Hi,
first of all, if you don't have experience in cisco, you need to hire someone that does, else it will be very difficult for you to get it working.
Then, on the router connected to the internet, you forward some ports to the internal server. And the default gateway of it, must have default route to said internet router.
In any case, write back when you have the hardware and the circuit working.
02-17-2008 05:02 AM
Thanks P.B,
I have working knowledge on cisco routers but when it comes complicated configurations I need a push.
The WIC ADSL is inserted and shows OK, Please advise what to do next, as mentioned.
Regards
02-17-2008 05:27 AM
Have you been given an username/password for the DSL ? Or a static address perhaps ?
02-17-2008 05:39 AM
Yes, its done. both pap and chap has given and CD is ok.
02-17-2008 10:04 AM
Let's try first with PPPoA that has no MTU reduction:
int atm0
pvc x/y <-- You need to know vp/vc values
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface dialer 0
dialer pool 1
dialer-group 1
ip address negotiated
ip nat outside
ppp pap sent-username xxx password zzzz
ppp ipcp dns request
ppp ipcp default route
int fa0/0
ip nat inside
dialer-list 1 protocol ip permit
ip nat inside static tcp
Note you must be able to ping citrix from router for this to work.
02-17-2008 10:44 PM
Hi P.b,
I already have three dialer interfaces (ADSL) which is used to connect branch offices. So should i change , dialer, pool, group numbers to 3?
Is that all configurations have i to apply? Please provide if anything left in your previous post. I am going to apply the changes and test it today evening, while the users are out.
Thanks again
02-18-2008 02:48 AM
Where do you have the dialer interfaces ? Do you have other dsl interface in the same router ?
The config should be enough to let people acces internal web server from outside.
02-18-2008 04:35 AM
The other interfaces are in same router. I have three dsl wics on it. The new one will be forth.
02-18-2008 04:52 AM
So yes you need a new dialer interface to keep setting separate.
02-18-2008 05:11 AM
Thanks, so it will be dialer3 and bridgegroup 3, right?
02-23-2008 12:56 AM
Dear p.b,
where will i put the DNS server addresses for this internet connection? which interface?
02-23-2008 05:17 AM
Hi,
do not worry about putting any DNS server for this connection, router doesn't need DNS.
02-23-2008 07:12 AM
The 'ppp ipcp default route' command doesnt accept in the dialer interface.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: