×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

vic2-2fxo not supported in 2811?

Answered Question
Feb 18th, 2008
User Badges:

i have a nm-hdv in slot one and a vic2-2fxo in the module. this 2811 has four hwic slots - can i put the vic2-2fxo in an hwic?


sh diag

Slot 1:

High Density Voice Port adapter

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.1

Top Assy. Part Number : 800-03567-01

Board Revision : G0

Deviation Number : 0-0

Fab Version : 02

PCB Serial Number : JAE07420BVK

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : NM-HDV=WIC Slot 0:

VG - FXO Voice daughter card (2 port)

WIC module not supported/disabled in this slot

Hardware Revision : 5.0

Top Assy. Part Number : 800-21597-01

Board Revision : E0

Deviation Number : 0-0

Fab Version : 04

PCB Serial Number : FOC09301FGD

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Version Identifier : V

Product (FRU) Number : VIC2-2FXO=


thanks in advance.

Correct Answer by paolo bevilacqua about 9 years 6 months ago

That is what I was telling you ... The ISR routers are really made to work this way ...


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
paolo bevilacqua Mon, 02/18/2008 - 22:43
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Yes, but you need the DSP modules on the router mainboard. The smaller is PVDM2-8 and will support 8 voice channels.


Hope this helps, please rate post if it does!

jerry.mcrae Tue, 02/19/2008 - 09:24
User Badges:

ok - im configuring this as a 911 line at a remote site. ill dig up DSP's and give it a shot.

thanks for the reply.

jerry.mcrae Tue, 02/19/2008 - 09:26
User Badges:

i have a pvdm2-64 sitting in a nm-hdv2-2t1/e1 - will this work?

paolo bevilacqua Tue, 02/19/2008 - 09:39
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Yes, although hugely oversized.

jerry.mcrae Tue, 02/19/2008 - 09:42
User Badges:

you said to put the pvdm2 on the motherboard and not on the nm-hdv?

jerry.mcrae Tue, 02/19/2008 - 10:18
User Badges:

i already have dsp on the motherboard.


PVDM Slot 0:

16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8538-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC1144176Z

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-16

Version Identifier : V01

EEPROM format version 4


PVDM Slot 1:

48-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8540-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC11372FMR

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-48

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

Correct Answer
paolo bevilacqua Wed, 02/20/2008 - 11:19
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

That is what I was telling you ... The ISR routers are really made to work this way ...


jerry.mcrae Fri, 02/22/2008 - 09:59
User Badges:

so i ended up removing the nm-hdv from slot 1 in the 2811 and adding the VIC2-2FXO in hwic slot 3 and the router found it - no more errors during a sh diag.


thanks.

Actions

This Discussion