UC500 Meet-Me CLI configuration...

Unanswered Question
Feb 26th, 2008
User Badges:

Does anyone know how to configure a meet-me conference on a UC500 via the CLI? The configuration notes for CME 4.2 don't seem to apply, since the UC500 does not have the required dspfarm pool. I would appreciate any help! Thanks, Dennis.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4.5 (2 ratings)
Loading.
paolo bevilacqua Tue, 02/26/2008 - 13:49
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Meet-me must use dspfarm, why do you say that is not in the uc500? Don't you see two voice-cards in config ?

dmorassut-sbi Tue, 02/26/2008 - 14:48
User Badges:

Thank you for your reply.


I'm new to the UC500 and CME platform in a lot of ways (coming from full server-based CallManager), so I might be missing something here. This is what I see from the command line:


Before Config:


#sh dsp

DSPFARM Configuration Information:

Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN

Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)

Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600

Connection check interval 600 Codec G729 VAD: ENABLED


Config (start):


dsp services dspfarm


After Config:


#sh dspfarm ?

all Display all DSPFARM global info

dsp Display DSPFARM DSPs information

profile Display DSPFARM profiles


#sh dspfarm all





Total number of DSPFARM DSP channel(s) 0


#sh dspfarm dsp active


Total number of DSPFARM DSP channel(s) 0


Am I on the right track?


Thanks,

Dennis.

paolo bevilacqua Wed, 02/27/2008 - 11:09
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Here's the config I use in a customer install, to support 2 x 8 parties G.711 conferencing only. There is only one set of ephone-dn for conference configured. The remember to cofngire the meet-me softkey in ephone-template.


voice-card 0

dspfarm

dsp services dspfarm

!

voice-card 1

no dspfarm


! recommend use of loopback

sccp local Loopback0

sccp ccm 10.6.4.200 identifier 6200 version 4.0

sccp

!

sccp ccm group 100

bind interface GigabitEthernet0/0.4

associate ccm 6200 priority 1

associate profile 10 register confdsp1

!

dspfarm profile 10 conference

codec g711ulaw

maximum sessions 2

associate application SCCP


telephony-service

sdspfarm units 1

sdspfarm tag 1 confdsp1

conference hardware

!

ephone-dn 192 dual-line

number 693

conference meetme

no huntstop

!

ephone-dn 193 dual-line

number 693

conference meetme

preference 1

no huntstop

!

!

ephone-dn 194 dual-line

number 693

conference meetme

preference 2

no huntstop

!

ephone-dn 195 dual-line

number 693

conference meetme

preference 3


Hope this helps, please rate post if it does!


dmorassut-sbi Wed, 02/27/2008 - 12:21
User Badges:

Thank you very much for this. I will give it a try and let you know how I make out.


Dennis.

dmorassut-sbi Tue, 08/19/2008 - 10:21
User Badges:

Picking this up again after some time and for a different customer location... this config really did help. Thank you.

mpitts Tue, 09/09/2008 - 09:37
User Badges:

Paolo,


This configuration also helped me, with a problem I had with the dspfarm not registering with SCCP on a UC500, except that I am using multi-party ad-hoc instead of meet me conference.


Everything now looks fine but when the folks press the Confrn softkey they get a message "no line available". The only thing I haven't tried is resetting the entire system.


I've attached the whole configuration in case there is something I've missed, but I think I have covered everything I could find in the documentation. If you could look through it when you have the time I would appreciate it.


Thanks,

Mike




Attachment: 

Actions

This Discussion